Every vanity in this collection is a 42-inch single-sink model, 22 inches deep, built in teak. Forty-two inches is the width people arrive at when 36 inches turns out to be slightly too small and 48 inches will not fit the wall, and it is an underrated size: half a foot of extra counter over the standard 36-inch vanity, in a footprint most bathrooms can still absorb. Teak is a dense, naturally oily hardwood that handles bathroom humidity better than almost anything else you can put in a wet room, and it is never MDF or particleboard. The Sonoma, Elizabeth, Atlanta, Chicago, Madison, Charlotte, Malibu, Catalina, Hampton, Pasadena, Parker, Manhattan, Santa Monica and Alys lines are all here.
Why 42 inches is worth considering
Most bathroom walls are not built to a catalogue size, and the gap between the 36-inch standard and the 48-inch step up is where a lot of renovations get stuck. A 42-inch vanity fills it. Compared with a 36-inch model you get a wider counter on both sides of the basin and a wider cabinet underneath, which is usually the difference between a drawer that closes and one that does not. Compared with a 48-inch model you lose six inches of counter but gain six inches of floor, which matters if the vanity sits near a door swing, a shower enclosure or a toilet. Measure the full run of wall and your door swing before deciding; if 42 fits with room to spare, look at 48 as well.
Floating and freestanding designs
The Madison Floating, Sonoma Reeded Floating and Hampton Floating models mount to the wall and leave the floor visible underneath, which makes a mid-size bathroom read larger and makes the floor easier to clean. They need a wall that can carry the load and plumbing that exits through the wall rather than the floor, so they are the more involved installation if your existing pipes come up through the floor. The freestanding designs, including Charlotte, Malibu, Elizabeth, Manhattan, Pasadena, Parker, Atlanta and the Catalina, rest on the floor and conceal the plumbing behind the base. That makes them the straightforward swap when you are replacing an existing vanity and would rather not open the wall.
Reeded, fluted and flat fronts
The lines differ mostly in how the fronts are treated. Sonoma is reeded and Catalina is a freestanding reeded design, both with vertical channels running across the fronts. Atlanta is the fluted line, where the same detail is cut into solid teak so each channel exposes grain running through it rather than sitting on the surface. Charlotte, Elizabeth, Malibu, Manhattan, Madison, Pasadena, Parker, Santa Monica and Alys give you plainer fronts where the teak grain itself is the detail. If you want texture, go reeded or fluted; if you want the wood to speak, the flatter fronts show more uninterrupted grain.
Teak, and how to look after it
Teak's natural oils are why it spent more than a century on boat decks, and why it belongs in a bathroom: it resists moisture and movement where softer woods swell. It is a genuine hardwood, responsibly and FSC-certified sourced, never MDF or particleboard, so the cabinet can be cleaned, sanded and refreshed over the years rather than chipping at the edges the way laminate does. Wipe spills instead of letting water stand at the seams, and use mild soap rather than abrasive or solvent cleaners. One note on materials: the Chicago Veneer model is finished in teak veneer rather than a solid teak front, so check that product page if solid teak specifically matters to you.
Countertops and installation
Depending on the design, tops are available in quartz or natural Carrara marble, finished with a mitered or cove edge. Teak is a warm, mid-to-dark wood, so a pale quartz gives you contrast while Carrara's grey veining reads cooler against it. The countertop is stone and ships in its own protective box rather than attached to the cabinet, with the undermount basin set at installation. Plan for an installer or plumber on delivery day.
Compare widths in our 42-inch vanities, 36-inch vanities and 48-inch vanities. Browse the full teak range, every single-sink vanity, and our wider solid wood collection. Countertop choices are explained in our vanity countertops guide.
42-inch teak vanity FAQ
Why choose a 42-inch vanity over 36 or 48?
Forty-two inches fills the gap when 36 inches feels cramped but 48 inches will not fit the wall. You gain counter and cabinet width over a 36-inch model while keeping six inches of floor that a 48-inch model would take, which matters near a door swing or a shower enclosure.
Are these vanities solid teak or a veneer?
The teak lines here are built in solid teak, a true hardwood chosen for how well it copes with bathroom humidity, never MDF or particleboard. The exception is the Chicago Veneer model, which is finished in teak veneer, so check that product page if the distinction matters to you.
Should I choose a floating or a freestanding model?
Floating models such as the Madison Floating, Sonoma Reeded Floating and Hampton Floating leave the floor visible and make a bathroom feel larger, but they need a wall that can carry the load and plumbing that exits through the wall. Freestanding models rest on the floor and hide the plumbing behind the base, which is the easier swap when replacing an existing vanity.
What is the difference between reeded, fluted and flat fronts?
Sonoma and Catalina are reeded and Atlanta is fluted, meaning vertical channels run across the fronts to create texture and shadow. The other lines have plainer fronts that show more uninterrupted teak grain.
What countertops are available, and is the sink pre-fitted?
Depending on the design, tops come in quartz or natural Carrara marble with a mitered or cove edge. The countertop is stone and ships in its own protective box rather than pre-fitted to the cabinet; the undermount basin is set during installation.