Wishlist

Cambridge 72 double sink vanity - drawing text version

Cambridge 72 in double sink vanity - drawing text version

This is a text version of the source drawings. Original drawing images are available through the PDF page links below. Keep the source warnings and unresolved dimensions in mind when using this text version.

Drawing text — flagged details need confirmation

Unresolved source dimensions are preserved and identified below. Obtain confirmed dimensions from Willow Bath and Vanity before installation, fabrication, or drilling.

Text equivalent of the ten source drawing pages. Original numeric labels and units are preserved. This is not a new engineering drawing or approval.

Each source page has its original drawing, a description of the view, and a table identifying what each dimension measures. Inches and millimeters are copied independently from the source; no conversion replaces a printed value.

Unresolved source dimensions

CAM-P10-REAR - source page 10

Rear inner-border offset: 1/1 in / 25 mm.

The source visibly prints 1/1, not a conventional 1-inch label. Its intended typography/dimension has not been approved.

Willow Bath and Vanity must confirm the intended inch label and whether 25 mm is the controlling dimension. No correction has been made.

Source page 1: Cambridge 72 in double sink bathroom vanity: overview

View original PDF — Source page 1: Cambridge 72 in double sink bathroom vanity: overview

Original drawing: Cambridge 72 in double sink bathroom vanity: overview.

Original source page 1, visually unchanged. Read this page's text equivalent.

View and dimensional relationships

An isometric line drawing shows the cabinet without a countertop. There are two wide outer bays with paired doors, a narrower central stack of front panels, horizontal upper fronts, a framed back, side panels, and legs beneath the cabinet. No dimensions are called out on this overview.

The cover identifies Willow Bath & Vanity and lists willowbathandvanity.com, info@willowbathandvanity.com, and 1-877-788-8444.

No dimension callouts are printed on this overview page.

Back to contents

Source page 2: Cambridge cabinet: front view

View original PDF — Source page 2: Cambridge cabinet: front view

Original drawing: Cambridge cabinet: front view.

Original source page 2, visually unchanged. Read this page's text equivalent.

View and dimensional relationships

The cabinet is shown straight on. The total width spans the outside left and right edges. Two wide door bays flank a narrower central stack. The three upper horizontal labels measure the individual framed bays, not three pieces whose sum is necessarily the outside width; stiles remain between them.

The 20-inch label runs across the vertical door region below the upper front. A dashed horizontal shelf/reference line within the left door bay is positioned by the 9-7/8-inch dimension from the lower door-region reference line. That dimension is not measured from the floor.

The central stack has two separately labeled 6-5/8-inch upper front bands and a 13-1/4-inch lower band. A leader to the lower central area reads: Double Drawer with Power Station and Organizer. This sheet does not specify electrical ratings.

On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.

Page 2 dimensions, as printed
Measurement Inches Millimeters Reference points / meaning
Overall cabinet width 71-1/8 1808 Outside left cabinet edge to outside right cabinet edge.
Overall cabinet height 33-1/2 850 Top of cabinet to bottom/floor reference line, including legs.
Left framed bay width 26-3/4 680 Width above the left door bay between its frame reference lines.
Center framed bay width 12-1/4 312 Width of central front stack between its vertical frame references.
Right framed bay width 26-3/4 680 Width above the right door bay between its frame reference lines.
Upper front band height 6-5/8 168 Left-side vertical label for the upper front band, above the doors.
Door region height 20 508 Region below the upper front band, down to the upper edge of the lower rail.
Shelf/reference height inside door bay 9-7/8 250 Dashed horizontal line above the lower door-region reference; not a floor height.
Central upper bands 6-5/8 each (two labels) 168 each Two successive upper central front bands.
Central lower band 13-1/4 338 Combined lower central front region under the two upper bands.

Source note: The source states: All measurements are +/- 1/4 inch. Values below are transcribed, not recalculated or approved for installation.

Back to contents

Source page 3: Cambridge cabinet: top view

View original PDF — Source page 3: Cambridge cabinet: top view

Original drawing: Cambridge cabinet: top view.

Original source page 3, visually unchanged. Read this page's text equivalent.

View and dimensional relationships

Looking down into the cabinet, large left and right compartments flank the narrower central drawer area. The outside width and depth enclose the whole cabinet. The 16-inch arrow lies inside the central drawer outline and runs in the front-to-back direction; it is not the full cabinet depth.

On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.

Page 3 dimensions, as printed
Measurement Inches Millimeters Reference points / meaning
Overall cabinet width 71-1/8 1808 Outside left-to-right span.
Overall cabinet depth 21-5/8 550 Outside rear-to-front span.
Central drawer outline depth 16 410 Internal front-to-back span marked within the central drawer outline.

Source note: The source states: All measurements are +/- 1/4 inch. Values below are transcribed, not recalculated or approved for installation.

Back to contents

Source page 4: Cambridge cabinet: back view

View original PDF — Source page 4: Cambridge cabinet: back view

Original drawing: Cambridge cabinet: back view.

Original source page 4, visually unchanged. Read this page's text equivalent.

View and dimensional relationships

The back panel contains two rounded rectangular plumbing openings, one behind each outer sink bay. All left/right directions in this section refer to looking at the rear of the cabinet. The horizontal chain starts at the left outside edge, crosses the first opening, the solid middle gap, and the second opening, then ends at the right outside edge.

The left-side vertical chain starts at the top of the cabinet, reaches the top edge of the openings, crosses their height, and then reaches the floor/bottom reference line. Thus the lower 16-3/8-inch segment is the opening-bottom height above that lower reference, not the opening height.

On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.

Page 4 dimensions, as printed
Measurement Inches Millimeters Reference points / meaning
Overall back width 71-1/8 1808 Outside left-to-right width.
Left edge to first opening 11 280 Horizontal distance from left outside edge to left edge of left plumbing opening.
Each plumbing opening width 8-5/8 (twice) 220 (twice) Horizontal width of each of the two rear openings.
Gap between openings 31-3/4 808 Horizontal distance between the right edge of the left opening and left edge of the right opening.
Second opening to right edge 11 280 Horizontal distance from right edge of right opening to right outside edge.
Top to opening top 6-1/2 165 Vertical distance from cabinet top to upper edge of the openings.
Plumbing opening height 10-5/8 270 Vertical height of each rear opening.
Opening bottom to lower reference 16-3/8 415 Vertical distance from lower edge of openings to the bottom/floor reference line.

Source note: The source states: All measurements are +/- 1/4 inch. Values below are transcribed, not recalculated or approved for installation.

Back to contents

Source page 5: Cambridge cabinet: side view

View original PDF — Source page 5: Cambridge cabinet: side view

Original drawing: Cambridge cabinet: side view.

Original source page 5, visually unchanged. Read this page's text equivalent.

View and dimensional relationships

The side outline is combined with dashed outlines of three drawer-box regions. The front/handle side is at the right of the drawing. Two shallow upper drawer-box regions and one taller lower region are dimensioned vertically. These are drawer-box dimensions in this side drawing, not the front-panel heights on page 2.

On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.

Page 5 dimensions, as printed
Measurement Inches Millimeters Reference points / meaning
Overall cabinet depth 21-5/8 550 Outside back-to-front span across the top.
Upper drawer-box height 3-3/4 96 Vertical dimension of the upper dashed drawer-box region.
Middle drawer-box height 3-3/4 96 Vertical dimension of the second dashed drawer-box region.
Lower drawer-box height 9-1/2 240 Vertical dimension of the larger lower dashed drawer-box region.

Source note: The source states: All measurements are +/- 1/4 inch. Values below are transcribed, not recalculated or approved for installation.

Back to contents

Source page 6: 72 in double sink 2 in straight mitered edge countertop: overview

View original PDF — Source page 6: 72 in double sink 2 in straight mitered edge countertop: overview

Original drawing: 72 in double sink 2 in straight mitered edge countertop: overview.

Original source page 6, visually unchanged. Read this page's text equivalent.

View and dimensional relationships

An isometric line drawing shows a rectangular top with two sink openings, one round faucet hole behind each opening, a tall straight front edge, and a separate upright backsplash along the rear. This page is an overview without dimension callouts. The dimensional drawing for this edge is page 7.

No dimension callouts are printed on this overview page.

Back to contents

Source page 7: 72 in double sink 2 in straight mitered countertop: dimensions

View original PDF — Source page 7: 72 in double sink 2 in straight mitered countertop: dimensions

Original drawing: 72 in double sink 2 in straight mitered countertop: dimensions.

Original source page 7, visually unchanged. Read this page's text equivalent.

View and dimensional relationships

This sheet has four related views: a separate backsplash elevation at the top, a front edge/profile elevation below it, a countertop plan beneath that, and a narrow side/profile view at the right. In the plan, the rear edge is at the top next to the faucet hole(s); the front edge is at the bottom.

Two rectangular sink openings are arranged left and right, with one faucet hole centered behind each opening. Horizontal dimension chains describe three different things: faucet centerlines, sink opening edges, and bracket-location columns. These chains must not be substituted for each other.

Small marks on both sides of the opening(s) are identified by the SINK BRACKET leader. The vertical bracket-location chain is separate from the chain describing the cutout depth. The drawing does not specify a bracket model or fastener size.

The straight edge elevation identifies a 45-degree mitered joint and a 2-inch edge height. The backsplash is a separate component; its height is not the countertop thickness.

On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.

Page 7 dimensions, as printed
Measurement Inches Millimeters Reference points / meaning
Backsplash length 72 1829 Left-to-right length of the separate backsplash elevation.
Backsplash height 3-7/8 100 Vertical height of the separate backsplash.
Backsplash thickness 3/4 20 Thickness shown in the narrow backsplash end view.
Countertop overall width 72 1829 Left-to-right outside width of the top in plan.
Countertop overall depth 22 560 Rear edge at the top of the plan to front edge at the bottom.
Left faucet center from left edge 15-3/4 400 Horizontal distance from left outside edge to center of left faucet hole.
Faucet center-to-center spacing 40-1/2 1028 Horizontal distance between the two faucet-hole centerlines.
Right faucet center from right edge 15-3/4 400 Horizontal distance from right faucet-hole centerline to right outside edge.
Left cutout from left edge 7 180 Horizontal distance from left outside edge to the left edge of the left sink cutout.
Each sink cutout width 17-3/8 440 Width of each rectangular opening; the same label is repeated under both openings.
Gap between sink cutouts 23-1/8 588 Horizontal solid span between the adjacent inside edges of the two sink openings.
Right cutout from right edge 7 180 Horizontal distance from right edge of right cutout to right outside edge.
Outer bracket columns from outside edges 4-7/8 (each side) 123 (each side) Horizontal end segments in the bracket-location chain, from each outside side edge to the nearest bracket column.
Bracket-column span around each sink 21-3/4 (each sink) 554 (each sink) Horizontal distance between the two bracket columns around a sink opening.
Gap between inside bracket columns 18-5/8 474 Horizontal gap between the right bracket column of the left sink and the left bracket column of the right sink.
Rear edge to faucet center 2-3/4 70 Faucet-hole center lies below the rear outside edge in the plan.
Faucet-hole diameter 1-3/8 35 Circular hole dimension; the Sonoma sheet prints a diameter symbol and Cambridge uses a leader to the circle.
Rear edge to cutout 5-1/2 140 Front-to-back segment from rear outside edge to rear edge of the rectangular sink opening.
Sink cutout depth 12-1/4 310 Front-to-back span of each rectangular sink opening.
Cutout to front edge 4-3/8 110 Front-to-back segment from front edge of the sink opening to front outside edge of the top.
Rear edge to upper bracket row 6-3/4 170 First segment of the front-to-back bracket-location chain, from rear edge toward the upper pair of bracket marks.
Bracket-row spacing 9-7/8 250 Middle front-to-back segment, between upper and lower bracket-location rows.
Lower bracket row to front edge 5-1/2 140 Last front-to-back segment in the bracket-location chain.
Sink cutout corner notation Not specified Not specified Drawing mark: 4-R10. Leader points to a rounded corner of the sink opening; the notation specifies four matching corners. No unit is printed beside this mark, so no new unit or radius conversion is supplied here.
Mitered edge height 2 50 Overall vertical fascia height in the edge elevation and side view.
Slab / return thickness labels 3/4 20 Repeated thickness callouts appear at slab/return ends and in the edge views.
Miter joint angle Not applicable Not applicable The source labels the straight-edge joint as 45 Degree Mitered Edge. This is an angle, not an inch or millimeter length.

Source note: The source states: All measurements are +/- 1/4 inch. Values below are transcribed, not recalculated or approved for installation.

Source note: The source explicitly limits this sheet to Straight Mitered Edge countertops and directs readers to the other edge section for that option.

Back to contents

Source page 8: Standard rectangular undermount sink

View original PDF — Source page 8: Standard rectangular undermount sink

Original drawing: Standard rectangular undermount sink.

Original source page 8, visually unchanged. Read this page's text equivalent.

View and dimensional relationships

The left drawing shows the rectangular rim and the bowl inside it. The hatched band is outside the inner opening. Sloping walls run from that opening toward the bowl floor. Two unlabeled apertures are shown along the centerline; this page does not give their diameters.

The right drawing is a side section of the same sink. Its height label is a sectional outside measurement as drawn, not a separately labeled usable water depth. The countertop cutout dimensions appear on pages 7 and 10 and are different from the sink dimensions on this page.

On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.

Page 8 dimensions, as printed
Measurement Inches Millimeters Reference points / meaning
Outside rim width 20-1/8 511 Left-to-right span across the outside edges of the hatched rim.
Outside rim depth 15 381 Front-to-back span across the outside edges of the rim.
Inner opening width 17-3/4 451 Left-to-right span at the inner edge of the rim, above the sloping bowl walls.
Inner opening depth 12-5/8 320.6 Front-to-back span at the inner edge of the rim.
Section height 7-5/8 193.6 Vertical dimension of the side section, between the upper and lower reference lines shown.

Source note: The source states: All measurements are +/- 1/4 inch. Values below are transcribed, not recalculated or approved for installation.

Back to contents

Source page 9: 72 in double sink 1.5 in double cove edge countertop: overview

View original PDF — Source page 9: 72 in double sink 1.5 in double cove edge countertop: overview

Original drawing: 72 in double sink 1.5 in double cove edge countertop: overview.

Original source page 9, visually unchanged. Read this page's text equivalent.

View and dimensional relationships

An isometric line drawing shows two sink openings and a faucet hole behind each, a layered shaped front/side edge, and an upright backsplash along the rear. This page is an overview without dimension callouts. The dimensional drawing for this edge is page 10.

No dimension callouts are printed on this overview page.

Back to contents

Source page 10: 72 in double sink 1.5 in double cove countertop: dimensions

View original PDF — Source page 10: 72 in double sink 1.5 in double cove countertop: dimensions

Original drawing: 72 in double sink 1.5 in double cove countertop: dimensions.

Original source page 10, visually unchanged. Read this page's text equivalent.

View and dimensional relationships

This sheet has four related views: a separate backsplash elevation at the top, a front edge/profile elevation below it, a countertop plan beneath that, and a narrow side/profile view at the right. In the plan, the rear edge is at the top next to the faucet hole(s); the front edge is at the bottom.

Two rectangular sink openings are arranged left and right, with one faucet hole centered behind each opening. Horizontal dimension chains describe three different things: faucet centerlines, sink opening edges, and bracket-location columns. These chains must not be substituted for each other.

Small marks on both sides of the opening(s) are identified by the SINK BRACKET leader. The vertical bracket-location chain is separate from the chain describing the cutout depth. The drawing does not specify a bracket model or fastener size.

The cove elevation shows a layered, shaped front profile and a separate shortened backsplash. Retain the actual profile dimension as printed rather than replacing it with the nominal 1.5-inch title.

On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.

Page 10 dimensions, as printed
Measurement Inches Millimeters Reference points / meaning
Backsplash length 69-7/8 1775 Left-to-right length of the separate backsplash elevation.
Backsplash height 3-7/8 100 Vertical height of the separate backsplash.
Backsplash thickness 3/4 20 Thickness shown in the narrow backsplash end view.
Countertop overall width 72 1829 Left-to-right outside width of the top in plan.
Countertop overall depth 22 560 Rear edge at the top of the plan to front edge at the bottom.
Left faucet center from left edge 15-3/4 400 Horizontal distance from left outside edge to center of left faucet hole.
Faucet center-to-center spacing 40-1/2 1028 Horizontal distance between the two faucet-hole centerlines.
Right faucet center from right edge 15-3/4 400 Horizontal distance from right faucet-hole centerline to right outside edge.
Left cutout from left edge 7 180 Horizontal distance from left outside edge to the left edge of the left sink cutout.
Each sink cutout width 17-3/8 440 Width of each rectangular opening; the same label is repeated under both openings.
Gap between sink cutouts 23-1/8 588 Horizontal solid span between the adjacent inside edges of the two sink openings.
Right cutout from right edge 7 180 Horizontal distance from right edge of right cutout to right outside edge.
Outer bracket columns from outside edges 4-7/8 (each side) 123 (each side) Horizontal end segments in the bracket-location chain, from each outside side edge to the nearest bracket column.
Bracket-column span around each sink 21-3/4 (each sink) 554 (each sink) Horizontal distance between the two bracket columns around a sink opening.
Gap between inside bracket columns 18-5/8 474 Horizontal gap between the right bracket column of the left sink and the left bracket column of the right sink.
Rear edge to faucet center 2-3/4 70 Faucet-hole center lies below the rear outside edge in the plan.
Faucet-hole diameter 1-3/8 35 Circular hole dimension; the Sonoma sheet prints a diameter symbol and Cambridge uses a leader to the circle.
Rear edge to cutout 5-1/2 140 Front-to-back segment from rear outside edge to rear edge of the rectangular sink opening.
Sink cutout depth 12-1/4 310 Front-to-back span of each rectangular sink opening.
Cutout to front edge 4-3/8 110 Front-to-back segment from front edge of the sink opening to front outside edge of the top.
Rear edge to upper bracket row 6-3/4 170 First segment of the front-to-back bracket-location chain, from rear edge toward the upper pair of bracket marks.
Bracket-row spacing 9-7/8 250 Middle front-to-back segment, between upper and lower bracket-location rows.
Lower bracket row to front edge 5-1/2 140 Last front-to-back segment in the bracket-location chain.
Sink cutout corner notation Not specified Not specified Drawing mark: 4-R20. Leader points to a rounded corner of the sink opening; the notation specifies four matching corners. No unit is printed beside this mark, so no new unit or radius conversion is supplied here.
Nominal profile in page title 1.5 Not stated in title This is the profile name printed in the heading; the drawn edge thickness is separately labeled below.
Drawn edge/profile thickness 1-5/8 40 Thickness dimension shown at the left of the elevation and again beside the side view.
Two elevation layers 3/4 + 3/4 20 + 20 Two stacked thicknesses are marked at the right end of the elevation.
Rear inner-border offset 1/1 25 Short offset between the rear outside edge and the dashed inner reference line.Unresolved: CAM-P10-REAR
Side inner-border offset 2 50 Offset from an outside side edge to the dashed inner line. Marked at the right on Cambridge and at the left on Sonoma.
Front inner-border offset 2 50 Offset from the front outside edge to the dashed inner line.

Source note: The source states: All measurements are +/- 1/4 inch. Values below are transcribed, not recalculated or approved for installation.

Source note: The source explicitly limits this sheet to Double Cove Edge countertops and directs readers to the other edge section for that option.

Source note: The rear-border label on this page remains unresolved: CAM-P10-REAR. The source values are preserved, not corrected.

Back to contents

Source and assistance

View the original source PDF. Source reviewed 19 November 2026.

Request an accessible format or a confirmed drawing, or call Willow Bath and Vanity at (877) 788-8444.

Updated 19 November 2026. This text version explains the source drawing; it is not a new installation specification.