Wishlist

Charlotte Teak 72 double sink vanity - drawing text version

Charlotte Teak 72 double-sink vanity - source drawing text version

This is a text version of the source drawings. Original drawing images are available through the PDF page links below. Keep the source warnings and unresolved dimensions in mind when using this text version.

Drawing text — flagged details need confirmation

All printed dimension labels are preserved without engineering approval. Obtain confirmed dimensions from Willow Bath and Vanity before installation, fabrication, or drilling.

Text equivalent of all ten original source pages. Printed labels and reference spans are preserved individually; no dimensions, units or accessory inclusion are inferred. The original source remains authoritative for what was printed, not necessarily for correct installation values.

Each source page has its original drawing, a description of the view, and a table identifying what each dimension measures. Inches and millimeters are copied independently from the source; no conversion replaces a printed value.

Source limitations

All printed measurement callouts, including repetitions, are retained separately. A source pair is not a newly calculated exact unit conversion.

The p2/p4 cabinet height label 34 in / 865 mm and p5 side height 34 in / 864 mm remain separate source labels. No reconciled replacement is invented.

CH72-P4-160 - source page 4

Unresolved lower rear-view label placement: 6-1/4 in / 160 mm.

This label is printed below the rear view near the separately labeled 69-3/4 inch / 1770 mm overall lower span, but no unambiguous pair of endpoints or leader is visible for the 160 mm label. It cannot safely be assigned to an opening offset or cabinet dimension.

Obtain a clarified source drawing identifying both reference endpoints before using this label for installation. No correction has been made.

CH72-P10-REAR - source page 10

Unusual printed rear inner-border fraction: 1/1 in / 25 mm.

The original rear inset callout visibly prints 1/1 inch alongside 25 mm. The unusual fraction is preserved literally; it has not been silently normalized or replaced.

Confirm the intended inch label and reference offset with Willow Bath and Vanity before installation. No correction has been made.

Source page 1: Cabinet overview

View original PDF — Source page 1: Cabinet overview

Original drawing: Cabinet overview.

Original source page 1, visually unchanged. Read this page's text equivalent.

View and dimensional relationships

The source cover identifies Charlotte Teak 72 IN Double Sink Bathroom Vanity. Its isometric line drawing shows a cabinet without a countertop, two outer paired-door bays with lower drawers, a central stack of four fronts, upper trim, framed sides and a shaped continuous base. The open top reveals internal partitions and rear openings. No dimensions are called out on this overview.

The cover identifies Willow Bath & Vanity and lists willowbathandvanity.com, info@willowbathandvanity.com, and 1-877-788-8444. The drawing illustrates the source cabinet rather than establishing accessories included with a purchase.

No dimension callouts are printed on this overview page.

Back to contents

Source page 2: Cabinet front view

View original PDF — Source page 2: Cabinet front view

Original drawing: Cabinet front view.

Original source page 2, visually unchanged. Read this page's text equivalent.

View and dimensional relationships

Two paired-door bays flank a central four-front stack. A broad drawer front lies beneath each paired-door bay. The top horizontal chain distinguishes outer trim, outer uprights, the two door-bay spans, central dividers and the center bay. Both the upper and lower overall widths are printed separately.

The left vertical chain runs through upper trim, the door region, the rail below it, the lower drawer region, a small lower transition and the base. The right chain uses different top, body, transition and base references. These are distinct drawn spans; they are not substituted for one another.

On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.

Page 2 dimensions, as printed
Measurement Inches Millimeters Reference points / meaning
Upper overall width 71-1/4 1811 Topmost horizontal dimension between the outside left and right upper references.
Left outer trim 3/4 20 Individual segment in the upper horizontal chain, read from left to right between the indicated adjacent vertical references.
Left outer upright 2 51 Individual segment in the upper horizontal chain, read from left to right between the indicated adjacent vertical references.
Left door-bay span 25-1/2 648 Individual segment in the upper horizontal chain, read from left to right between the indicated adjacent vertical references.
Left center divider 1 25 Individual segment in the upper horizontal chain, read from left to right between the indicated adjacent vertical references.
Central front bay 12-3/4 325 Individual segment in the upper horizontal chain, read from left to right between the indicated adjacent vertical references.
Right center divider 1 25 Individual segment in the upper horizontal chain, read from left to right between the indicated adjacent vertical references.
Right door-bay span 25-1/2 648 Individual segment in the upper horizontal chain, read from left to right between the indicated adjacent vertical references.
Right outer upright 2 51 Individual segment in the upper horizontal chain, read from left to right between the indicated adjacent vertical references.
Right outer trim 3/4 20 Individual segment in the upper horizontal chain, read from left to right between the indicated adjacent vertical references.
Left chain: upper trim span 3/4 20 Individual segment of the left vertical chain, following its adjacent horizontal reference lines from top toward the lower floor/base reference.
Left chain: door-region height 20-1/8 511 Individual segment of the left vertical chain, following its adjacent horizontal reference lines from top toward the lower floor/base reference.
Left chain: rail below doors 1 25 Individual segment of the left vertical chain, following its adjacent horizontal reference lines from top toward the lower floor/base reference.
Left chain: lower drawer region 5-3/4 147 Individual segment of the left vertical chain, following its adjacent horizontal reference lines from top toward the lower floor/base reference.
Left chain: lower transition 5/8 15 Individual segment of the left vertical chain, following its adjacent horizontal reference lines from top toward the lower floor/base reference.
Left chain: base region 4-3/4 122 Individual segment of the left vertical chain, following its adjacent horizontal reference lines from top toward the lower floor/base reference.
Right chain: upper span 1 25 Short upper dimension from the upper outside line to the nearby lower trim/body reference.
Right chain: body span 29-1/4 744 Long right-side vertical span from the upper reference to the base transition reference shown.
Right chain: transition span 3/8 10 Small vertical segment at the right just above the lower base span.
Right chain: lower base span 4-3/8 112 Lower right-side span down to the floor/base reference.
Right overall height 34 865 Outermost right vertical dimension from the upper cabinet reference to the bottom base/floor line.
Lower overall width 71-1/4 1811 Full width between the outside left and right base references, separately repeated beneath the elevation.

Source note: The source states: All measurements are plus or minus 1/4 inch. Values are transcribed as printed, not recalculated or approved for installation.

Back to contents

Source page 3: Cabinet top view

View original PDF — Source page 3: Cabinet top view

Original drawing: Cabinet top view.

Original source page 3, visually unchanged. Read this page's text equivalent.

View and dimensional relationships

The top plan shows two broad outer compartments with U-shaped interruptions, a narrow central drawer outline and an outer frame. The upper edge of the view is the rear; handles project at the lower front edge. The drawing does not separately dimension the U-shaped interruptions.

Several width and depth chains describe different reference lines. The 65-3/4-inch internal width is printed above and below the view. The right-side 20-7/8-inch span plus its separate 3/4-inch front segment is distinct from the left-side overall 21-3/4-inch dimension.

On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.

Page 3 dimensions, as printed
Measurement Inches Millimeters Reference points / meaning
Upper overall width 71-1/4 1811 Outermost upper horizontal span between the outside cabinet references.
Upper inner width 65-3/4 1669 Nested horizontal span between the two inner side references.
Left inner bay 25-1/2 648 Individual segment in the innermost upper horizontal chain, read from left to right.
Left partition 1 25 Individual segment in the innermost upper horizontal chain, read from left to right.
Central inner bay 12-3/4 325 Individual segment in the innermost upper horizontal chain, read from left to right.
Right partition 1 25 Individual segment in the innermost upper horizontal chain, read from left to right.
Right inner bay 25-1/2 648 Individual segment in the innermost upper horizontal chain, read from left to right.
Left overall depth 21-3/4 551 Outermost left vertical dimension between rear and front outside references.
Left depth chain: rear band 2 51 Individual segment in the left inner vertical depth chain, from rear toward front.
Left depth chain: middle span 16-7/8 429 Individual segment in the left inner vertical depth chain, from rear toward front.
Left depth chain: front band 2 51 Individual segment in the left inner vertical depth chain, from rear toward front.
Right main depth reference 20-7/8 531 Right-side vertical span from the rear outside reference to the inset front reference.
Right front depth segment 3/4 20 Short right-side span from the inset front reference to the front outside reference.
Lower left outer strip 3/4 20 Separate small horizontal span at the indicated end of the lower width chain.
Lower left inner strip 2 51 Separate small horizontal span at the indicated end of the lower width chain.
Lower right inner strip 2 51 Separate small horizontal span at the indicated end of the lower width chain.
Lower right outer strip 3/4 20 Separate small horizontal span at the indicated end of the lower width chain.
Lower inner width 65-3/4 1669 The inner left-to-right reference span repeated below the plan.

Source note: The source states: All measurements are plus or minus 1/4 inch. Values are transcribed as printed, not recalculated or approved for installation.

Back to contents

Source page 4: Cabinet rear view

View original PDF — Source page 4: Cabinet rear view

Original drawing: Cabinet rear view.

Original source page 4, visually unchanged. Read this page's text equivalent.

View and dimensional relationships

The rear has two rectangular openings separated by a narrow central region and framed outer panels. Left and right here refer to looking at the back. The left opening has separately printed width and height labels; its top offset and distance to the adjacent inner upright are also shown. The right opening has no separate set of these callouts.

Upper width chains describe the overall upper width, inner width, outer trim/uprights and individual rear-panel framing spans. The bottom chain labels a lower 69-3/4-inch width and two outer 3/4-inch spans. A separate 6-1/4-inch / 160 mm label is printed near that lower chain without unambiguous reference endpoints; this label is retained as unresolved, not assigned to plumbing or cabinet construction.

The left and right vertical chains use different panel/rail/base references. The two chains are reported as drawn rather than combined into a replacement dimension.

On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.

Page 4 dimensions, as printed
Measurement Inches Millimeters Reference points / meaning
Upper overall width 71-1/4 1811 Topmost full horizontal span between the outside upper references.
Upper inner width 65-3/4 1669 Nested width between the indicated inner side references.
Upper left outer trim 3/4 20 Separate horizontal span at the indicated end of the upper width chain.
Upper left upright 2 51 Separate horizontal span at the indicated end of the upper width chain.
Upper right upright 2 51 Separate horizontal span at the indicated end of the upper width chain.
Upper right outer trim 3/4 20 Separate horizontal span at the indicated end of the upper width chain.
Left outer inner-frame strip 1-5/8 41 Individual segment of the interior horizontal rear-frame chain, read left to right between adjacent reference lines.
Left rear panel span 23-5/8 599 Individual segment of the interior horizontal rear-frame chain, read left to right between adjacent reference lines.
Left central frame strip 1-5/8 41 Individual segment of the interior horizontal rear-frame chain, read left to right between adjacent reference lines.
Central rear span 12-1/4 310 Individual segment of the interior horizontal rear-frame chain, read left to right between adjacent reference lines.
Right central frame strip 1-5/8 41 Individual segment of the interior horizontal rear-frame chain, read left to right between adjacent reference lines.
Right rear panel span 23-5/8 599 Individual segment of the interior horizontal rear-frame chain, read left to right between adjacent reference lines.
Right outer inner-frame strip 1-5/8 41 Individual segment of the interior horizontal rear-frame chain, read left to right between adjacent reference lines.
Left overall height 34 865 Outermost left vertical span from upper cabinet reference to bottom base/floor line.
Left body reference span 29-1/4 744 Long left-side span above the lower base reference.
Left lower base span 4-3/4 122 Short lower left span between the body/base transition and bottom base/floor line.
Right upper band 5-1/8 130 Individual segment in the right vertical chain from the top downward, between its adjacent horizontal references.
Right main rear panel span 23-1/4 589 Individual segment in the right vertical chain from the top downward, between its adjacent horizontal references.
Right lower rail span 2-1/4 56 Individual segment in the right vertical chain from the top downward, between its adjacent horizontal references.
Right lowest base span 3-5/8 91 Individual segment in the right vertical chain from the top downward, between its adjacent horizontal references.
Left rear opening width 7-7/8 201 Horizontal dimension across the left rectangular opening.
Left rear opening height 7-7/8 201 Vertical dimension across the left rectangular opening.
Left opening top offset 4-1/4 107 Vertical distance from the underside of the upper rear band to the top of the left opening.
Left opening to inner upright 8-1/2 216 Horizontal distance from the right side of the left opening to the nearby inner-upright reference on its right.
Lower reference width 69-3/4 1770 Bottom horizontal width between the inset lower left and right references; separate outer trim spans are shown at its ends.
Lower left outer trim 3/4 20 Short horizontal span at the left end of the bottom width chain.
Lower right outer trim 3/4 20 Short horizontal span at the right end of the bottom width chain.
Unassigned lower label 6-1/4 160 Printed near the lower width chain without a clear independent pair of endpoints or leader. No plumbing-offset or other construction meaning is assigned.Unresolved: CH72-P4-160

Source note: The source states: All measurements are plus or minus 1/4 inch. Values are transcribed as printed, not recalculated or approved for installation.

Source note: CH72-P4-160: the reference endpoints for the lower 160 mm label require clarification.

Back to contents

Source page 5: Cabinet side view

View original PDF — Source page 5: Cabinet side view

Original drawing: Cabinet side view.

Original source page 5, visually unchanged. Read this page's text equivalent.

View and dimensional relationships

The side elevation shows a framed panel, top trim and shaped base; the front and handles are on the left. The top depth chain contains a separate 3/8-inch projection/reference offset, two 2-inch uprights and a 17-1/4-inch center span. The upper 21-1/4-inch span and lower 21-3/4-inch depth use distinct references.

The overall side height is printed as 34 inches / 864 mm; front and rear views separately print 34 inches / 865 mm. Both are retained without manufacturing a reconciled replacement. The right vertical chain separates the upper band, panel, lower rail and base.

On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.

Page 5 dimensions, as printed
Measurement Inches Millimeters Reference points / meaning
Upper main depth span 21-1/4 541 Upper horizontal span from the inset front reference to the rear outside reference.
Front upright span 2 51 Individual segment of the upper depth chain, read from the front at left toward the rear at right.
Side panel horizontal span 17-1/4 439 Individual segment of the upper depth chain, read from the front at left toward the rear at right.
Rear upright span 2 51 Individual segment of the upper depth chain, read from the front at left toward the rear at right.
Upper front offset 3/8 10 Small horizontal distance between the outer front projection reference and the adjacent inset reference.
Overall side height 34 864 Outermost left vertical dimension from upper cabinet to lower base/floor reference; preserved separately from the 865 mm front/rear label.
Upper side band 3 76 Individual segment of the right-side vertical chain, read from top to bottom between adjacent references.
Side panel vertical span 24-1/4 617 Individual segment of the right-side vertical chain, read from top to bottom between adjacent references.
Lower side rail 2 51 Individual segment of the right-side vertical chain, read from top to bottom between adjacent references.
Side base span 4-3/4 122 Individual segment of the right-side vertical chain, read from top to bottom between adjacent references.
Lower outside depth 21-3/4 551 Full horizontal span between the outside front and rear base references below the elevation.

Source note: The source states: All measurements are plus or minus 1/4 inch. Values are transcribed as printed, not recalculated or approved for installation.

Back to contents

Source page 6: 72 in double sink 2 in straight mitered edge countertop: overview

View original PDF — Source page 6: 72 in double sink 2 in straight mitered edge countertop: overview

Original drawing: 72 in double sink 2 in straight mitered edge countertop: overview.

Original source page 6, visually unchanged. Read this page's text equivalent.

View and dimensional relationships

An isometric line drawing shows a rectangular top with two sink openings, one round faucet hole behind each opening, a tall straight front edge, and a separate upright backsplash along the rear. This page is an overview without dimension callouts. The dimensional drawing for this edge is page 7.

No dimension callouts are printed on this overview page.

Back to contents

Source page 7: Straight-mitered countertop and backsplash

View original PDF — Source page 7: Straight-mitered countertop and backsplash

Original drawing: Straight-mitered countertop and backsplash.

Original source page 7, visually unchanged. Read this page's text equivalent.

View and dimensional relationships

The sheet includes a separate backsplash elevation and end view, a countertop front-profile elevation, a plan with two sink openings and one faucet hole behind each, and a narrow side/profile view. The top of the plan is the rear and its bottom is the front.

The faucet-axis chain, sink-opening chain and bracket-location chain are different measurements. Small marks beside each opening are identified by the SINK BRACKET leader. Their vertical location chain is separate from the opening-depth chain. The drawing gives no bracket model or fastener size.

Two separate leaders say 45 Degree Mitered Edge: one points to the dashed joint in the elevation and another to the front-right corner in plan. The printed edge height is 2 inches / 50 mm. The separate backsplash height is not the countertop thickness.

On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.

Page 7 dimensions, as printed
Measurement Inches Millimeters Reference points / meaning
Backsplash length 72 1829 Full horizontal span of the separate backsplash elevation.
Backsplash height 3-7/8 100 Vertical span of the separate backsplash, not countertop profile height.
Backsplash thickness 3/4 20 Horizontal span of the narrow backsplash end view.
Front elevation profile height 2 50 Vertical profile-height dimension on the left of the front edge elevation.
Front elevation left return thickness 3/4 20 Separate short thickness dimension at the left end of the front elevation.
Front elevation right return thickness 3/4 20 Separate short thickness dimension at the right end of the front elevation.
Plan overall width 72 1829 Outside left-to-right span of the countertop in plan.
Left faucet-axis offset 15-3/4 400 Left outside edge to left faucet-hole centerline.
Faucet-axis spacing 40-1/2 1028 Horizontal distance between the two faucet-hole centerlines.
Right faucet-axis offset 15-3/4 400 Right faucet-hole centerline to right outside edge.
Plan overall depth 22 560 Rear outside edge to front outside edge of the countertop.
Rear edge to sink opening 5-1/2 140 Upper segment of the left vertical chain, rear outside edge to rear edge of the left sink opening.
Sink opening depth 12-1/4 310 Middle segment of the left vertical chain across the opening from rear to front.
Sink opening to front edge 4-3/8 110 Lower segment of the left vertical chain, opening front edge to countertop front edge.
Rear edge to faucet center 2-3/4 70 Short vertical span near the left faucet hole, from the rear edge to its center.
Faucet-hole circular callout 1-3/8 35 Leader to the circular left faucet hole; the printed circular-hole size is preserved.
Rear edge to rear bracket row 6-3/4 170 Upper segment of the internal bracket-location chain from rear edge to rear bracket row.
Bracket-row separation 9-7/8 250 Middle segment between the rear and front bracket-location rows.
Front bracket row to front edge 5-1/2 140 Lower segment from front bracket row to outside front edge.
Left outside edge to left opening 7 180 First segment in the opening-edge chain beneath the plan.
Left sink opening width 17-3/8 440 Second segment across the left sink opening.
Solid span between openings 23-1/8 588 Middle segment between the inside edges of the two openings.
Right sink opening width 17-3/8 440 Fourth segment across the right sink opening.
Right opening to right outside edge 7 180 Last segment of the opening-edge chain.
Left outer bracket offset 4-7/8 123 Left outside edge to outer bracket column of the left sink.
Left bracket-column spacing 21-3/4 554 Horizontal spacing between bracket columns around the left sink.
Gap between inner bracket columns 18-5/8 474 Horizontal gap between the inner bracket columns of the two sinks.
Right bracket-column spacing 21-3/4 554 Horizontal spacing between bracket columns around the right sink.
Right outer bracket offset 4-7/8 123 Outer bracket column of the right sink to right outside edge.
Right side-profile height 2 50 Transverse span across the narrow right-hand profile view, independently repeated from the elevation.
Right profile upper thickness 3/4 20 Upper vertical thickness callout on the narrow right-hand profile view.
Right profile lower thickness 3/4 20 Lower vertical thickness callout on the narrow right-hand profile view.
Sink opening corner notation Not printed Not printed Literal source notation 4-R10 with a leader to a rounded sink-opening corner. No unit is printed beside the notation, so no unit or conversion is invented.

Source note: The source states: All measurements are plus or minus 1/4 inch. Values are transcribed as printed, not recalculated or approved for installation.

Source note: The source limits this page to Straight Mitered Edge countertops and directs readers to the other edge section for that option.

Back to contents

Source page 8: Standard rectangular undermount sink

View original PDF — Source page 8: Standard rectangular undermount sink

Original drawing: Standard rectangular undermount sink.

Original source page 8, visually unchanged. Read this page's text equivalent.

View and dimensional relationships

The left drawing shows the rectangular rim and the bowl inside it. The hatched band is outside the inner opening. Sloping walls run from that opening toward the bowl floor. Two unlabeled apertures are shown along the centerline; this page does not give their diameters.

The right drawing is a side section of the same sink. Its height label is a sectional outside measurement as drawn, not a separately labeled usable water depth. The countertop cutout dimensions appear on pages 7 and 10 and are different from the sink dimensions on this page.

On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.

Page 8 dimensions, as printed
Measurement Inches Millimeters Reference points / meaning
Outside rim width 20-1/8 511 Left-to-right span across the outside edges of the hatched rim.
Outside rim depth 15 381 Front-to-back span across the outside edges of the rim.
Inner opening width 17-3/4 451 Left-to-right span at the inner edge of the rim, above the sloping bowl walls.
Inner opening depth 12-5/8 320.6 Front-to-back span at the inner edge of the rim.
Section height 7-5/8 193.6 Vertical dimension of the side section, between the upper and lower reference lines shown.

Source note: The source states: All measurements are +/- 1/4 inch. Values below are transcribed, not recalculated or approved for installation.

Back to contents

Source page 9: 72 in double sink 1.5 in double cove edge countertop: overview

View original PDF — Source page 9: 72 in double sink 1.5 in double cove edge countertop: overview

Original drawing: 72 in double sink 1.5 in double cove edge countertop: overview.

Original source page 9, visually unchanged. Read this page's text equivalent.

View and dimensional relationships

An isometric line drawing shows two sink openings and a faucet hole behind each, a layered shaped front/side edge, and an upright backsplash along the rear. This page is an overview without dimension callouts. The dimensional drawing for this edge is page 10.

No dimension callouts are printed on this overview page.

Back to contents

Source page 10: Double-cove countertop and backsplash

View original PDF — Source page 10: Double-cove countertop and backsplash

Original drawing: Double-cove countertop and backsplash.

Original source page 10, visually unchanged. Read this page's text equivalent.

View and dimensional relationships

The sheet includes a separate backsplash elevation and end view, a countertop front-profile elevation, a plan with two sink openings and one faucet hole behind each, and a narrow side/profile view. The top of the plan is the rear and its bottom is the front.

The faucet-axis chain, sink-opening chain and bracket-location chain are different measurements. Small marks beside each opening are identified by the SINK BRACKET leader. Their vertical location chain is separate from the opening-depth chain. The drawing gives no bracket model or fastener size.

The page title calls this the 1.5 IN DOUBLE COVE EDGE option. The drawn profile separately states 1-5/8 inch / 40 mm, with two 3/4 inch / 20 mm elevation layers. The nominal title and printed detail remain separate source information. The rear inner-border callout visibly prints 1/1 inch / 25 mm; that unusual label is retained pending clarification.

On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.

Page 10 dimensions, as printed
Measurement Inches Millimeters Reference points / meaning
Backsplash length 69-7/8 1775 Full horizontal span of the separate backsplash elevation.
Backsplash height 3-7/8 100 Vertical span of the separate backsplash, not countertop profile height.
Backsplash thickness 3/4 20 Horizontal span of the narrow backsplash end view.
Front elevation profile height 1-5/8 40 Vertical profile-height dimension on the left of the front edge elevation.
Front elevation layer 1 3/4 20 Separate upper layer thickness at the right of the front elevation.
Front elevation layer 2 3/4 20 Separate lower layer thickness at the right of the front elevation.
Plan overall width 72 1829 Outside left-to-right span of the countertop in plan.
Left faucet-axis offset 15-3/4 400 Left outside edge to left faucet-hole centerline.
Faucet-axis spacing 40-1/2 1028 Horizontal distance between the two faucet-hole centerlines.
Right faucet-axis offset 15-3/4 400 Right faucet-hole centerline to right outside edge.
Plan overall depth 22 560 Rear outside edge to front outside edge of the countertop.
Rear edge to sink opening 5-1/2 140 Upper segment of the left vertical chain, rear outside edge to rear edge of the left sink opening.
Sink opening depth 12-1/4 310 Middle segment of the left vertical chain across the opening from rear to front.
Sink opening to front edge 4-3/8 110 Lower segment of the left vertical chain, opening front edge to countertop front edge.
Rear edge to faucet center 2-3/4 70 Short vertical span near the left faucet hole, from the rear edge to its center.
Faucet-hole circular callout 1-3/8 35 Leader to the circular left faucet hole; the printed circular-hole size is preserved.
Rear edge to rear bracket row 6-3/4 170 Upper segment of the internal bracket-location chain from rear edge to rear bracket row.
Bracket-row separation 9-7/8 250 Middle segment between the rear and front bracket-location rows.
Front bracket row to front edge 5-1/2 140 Lower segment from front bracket row to outside front edge.
Left outside edge to left opening 7 180 First segment in the opening-edge chain beneath the plan.
Left sink opening width 17-3/8 440 Second segment across the left sink opening.
Solid span between openings 23-1/8 588 Middle segment between the inside edges of the two openings.
Right sink opening width 17-3/8 440 Fourth segment across the right sink opening.
Right opening to right outside edge 7 180 Last segment of the opening-edge chain.
Left outer bracket offset 4-7/8 123 Left outside edge to outer bracket column of the left sink.
Left bracket-column spacing 21-3/4 554 Horizontal spacing between bracket columns around the left sink.
Gap between inner bracket columns 18-5/8 474 Horizontal gap between the inner bracket columns of the two sinks.
Right bracket-column spacing 21-3/4 554 Horizontal spacing between bracket columns around the right sink.
Right outer bracket offset 4-7/8 123 Outer bracket column of the right sink to right outside edge.
Right side-profile height 1-5/8 40 Transverse span across the narrow right-hand profile view, independently repeated from the elevation.
Rear inner-border offset 1/1 25 Small vertical rear-edge to dashed-inner-line dimension at the top-right of the plan. Literal unusual fraction retained.Unresolved: CH72-P10-REAR
Right inner-border offset 2 50 Short horizontal span between the right outside edge and nearby dashed inner reference.
Front inner-border offset 2 50 Short vertical span between the front outside edge and nearby dashed inner reference.
Sink opening corner notation Not printed Not printed Literal source notation 4-R20 with a leader to a rounded sink-opening corner. No unit is printed beside the notation, so no unit or conversion is invented.

Source note: The source states: All measurements are plus or minus 1/4 inch. Values are transcribed as printed, not recalculated or approved for installation.

Source note: The source limits this page to Double Cove Edge countertops and directs readers to the other edge section for that option.

Back to contents

Source and assistance

View the original source PDF. Source reviewed 19 November 2026.

Request an accessible format or a confirmed drawing, or call Willow Bath and Vanity at (877) 788-8444.

Updated 19 November 2026. This text version explains the source drawing; it is not a new installation specification.