Charlotte Teak 84 double sink vanity - drawing text version
Charlotte Teak 84 double-sink vanity - source drawing text version
PDF with text descriptions — 26 pages.
This is a text version of the source drawings. Original drawing images are available through the PDF page links below. Keep the source warnings and unresolved dimensions in mind when using this text version.
All printed dimension labels are preserved without engineering approval. Obtain confirmed dimensions from Willow Bath and Vanity before installation, fabrication, or drilling.
Text companion to all ten source pages, preserving every printed dimension callout, missing unit counterpart and distinct reference chain. No engineering dimensions are inferred or approved.
Each source page has its original drawing, a description of the view, and a table identifying what each dimension measures. Inches and millimeters are copied independently from the source; no conversion replaces a printed value.
Source limitations
This text version covers all ten source pages for this model.
Page 2 has two vertical 1-inch gap labels without printed millimeter counterparts; page 4 has two 41 mm end labels without printed inch counterparts. These remain explicitly unpaired, without conversion.
Dimensions describe drawing references, not confirmation of accessories included in a purchased configuration.
CH84-P10-REAR - source page 10
Unusual printed rear inner-border fraction: 1/1 in / 25 mm.
The original rear inset callout visibly prints 1/1 inch alongside 25 mm. The unusual fraction is preserved literally; it has not been silently normalized or replaced.
Confirm the intended inch label and reference offset with Willow Bath and Vanity before installation. No correction has been made.
Source page 1: Charlotte Teak 84 double-sink cabinet overview
View original PDF — Source page 1: Charlotte Teak 84 double-sink cabinet overview
Original drawing: Charlotte Teak 84 double-sink cabinet overview.
Original source page 1, visually unchanged. Read this page's text equivalent.
View and dimensional relationships
Perspective of a wide open-top cabinet on a shaped base. Three narrow four-front columns stand at left, center and right. Two paired-door bays lie between them, each with a broad lower drawer. Internal boxes, dividers, rear rectangular cutouts and bar handles are visible. No countertop is shown. The title identifies CHARLOTTE TEAK 84 IN DOUBLE SINK BATHROOM VANITY; no dimension callouts occur here.
Source branding: Willow Bath and Vanity. Footer contact: willowbathandvanity.com; info@willowbathandvanity.com;1-877-788-8444.
No dimension callouts are printed on this overview page.
Source page 2: Cabinet front view
View original PDF — Source page 2: Cabinet front view
Original drawing: Cabinet front view.
Original source page 2, visually unchanged. Read this page's text equivalent.
View and dimensional relationships
Front elevation contains three narrow four-front columns, at left, center and right. Two paired-door bays lie between them, each with a broad lower drawer. The horizontal chain separately identifies fronts, dividers, uprights and outer projections. Left and right vertical chains use distinct reference levels.
On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.
| Measurement | Inches | Millimeters | Reference points / meaning |
|---|---|---|---|
| Overall upper cabinet width | 83-1/4 | 2116 | Outermost upper horizontal span, from left to right projected cabinet edge. |
| Left projection | 3/4 | 20 | Individual segment of the upper horizontal front chain, read from left to right between adjacent reference lines. |
| Left upright | 2 | 51 | Individual segment of the upper horizontal front chain, read from left to right between adjacent reference lines. |
| Left narrow front | 9-3/4 | 246 | Individual segment of the upper horizontal front chain, read from left to right between adjacent reference lines. |
| First divider | 1 | 25 | Individual segment of the upper horizontal front chain, read from left to right between adjacent reference lines. |
| Left paired-door bay | 22-3/8 | 569 | Individual segment of the upper horizontal front chain, read from left to right between adjacent reference lines. |
| Second divider | 1 | 25 | Individual segment of the upper horizontal front chain, read from left to right between adjacent reference lines. |
| Center narrow front | 9-3/4 | 246 | Individual segment of the upper horizontal front chain, read from left to right between adjacent reference lines. |
| Third divider | 1 | 25 | Individual segment of the upper horizontal front chain, read from left to right between adjacent reference lines. |
| Right paired-door bay | 22-3/8 | 569 | Individual segment of the upper horizontal front chain, read from left to right between adjacent reference lines. |
| Fourth divider | 1 | 25 | Individual segment of the upper horizontal front chain, read from left to right between adjacent reference lines. |
| Right narrow front | 9-3/4 | 246 | Individual segment of the upper horizontal front chain, read from left to right between adjacent reference lines. |
| Right upright | 2 | 51 | Individual segment of the upper horizontal front chain, read from left to right between adjacent reference lines. |
| Right projection | 3/4 | 20 | Individual segment of the upper horizontal front chain, read from left to right between adjacent reference lines. |
| Overall cabinet height | 34 | 864 | Outer left vertical span from cabinet top to base bottom reference. |
| Upper left trim span | 3/4 | 20 | Small vertical span at the upper left trim, between the adjacent indicated levels. |
| Upper right trim span | 1 | 25 | Small vertical span at the upper right trim, retained separately from the upper-left trim reference. |
| Main front vertical span | 27-3/4 | 704 | Right vertical span from below the upper trim reference to the lower front/base reference. |
| Left base height | 4-3/4 | 122 | Lower left vertical span across the base. |
| Right base height | 4-3/4 | 122 | Independently repeated lower right vertical span across the base. |
| Upper left drawer-front span | 6-1/4 | 158 | First left vertical front segment below the upper trim. |
| First left front gap | 1 | Not printed | Short vertical separator between the first and second measured drawer-front spans; no millimeter label is printed. |
| Second left drawer-front span | 6-1/4 | 158 | Second left vertical measured drawer-front segment. |
| Second left front gap | 1 | Not printed | Short separator below the second measured front; no millimeter label is printed. |
| Lower combined front span | 12-5/8 | 320 | Left vertical span across the two lower narrow drawer fronts together. |
| Lower front rail span | 5/8 | 15 | Short left vertical span below the combined lower fronts and above the base. |
| Raised base underside clearance | 3-1/4 | 84 | Short vertical reference at the base cutout, from the lower base/floor level to the raised underside. |
| Overall lower cabinet width | 83-1/4 | 2116 | Repeated full outside horizontal width beneath the base. |
Source note: The source states: All measurements are plus or minus 1/4 inch. Values are copied as printed, not converted or approved for installation.
Source note: Two 1-inch separator labels have no printed millimeter value; no conversion is supplied.
Source page 3: Cabinet top view
View original PDF — Source page 3: Cabinet top view
Original drawing: Cabinet top view.
Original source page 3, visually unchanged. Read this page's text equivalent.
View and dimensional relationships
The open top plan shows three narrow drawer boxes alternating with two broad sink bays with U-shaped internal clearance cutouts. Width chains locate bays and dividers. The drawing separately dimensions overall depth, inner depth and frame/projecting spans; it does not dimension each U-shaped cutout.
On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.
| Measurement | Inches | Millimeters | Reference points / meaning |
|---|---|---|---|
| Overall upper width | 83-1/4 | 2116 | Outermost horizontal span above the top view. |
| Upper inner width | 77-3/4 | 1976 | Upper inner span between the two inner side-frame references. |
| Left narrow front | 9-3/4 | 246 | Individual segment of the upper internal bay chain, left to right between adjacent frame/divider references. |
| First divider | 1 | 25 | Individual segment of the upper internal bay chain, left to right between adjacent frame/divider references. |
| Left paired-door bay | 22-3/8 | 569 | Individual segment of the upper internal bay chain, left to right between adjacent frame/divider references. |
| Second divider | 1 | 25 | Individual segment of the upper internal bay chain, left to right between adjacent frame/divider references. |
| Center narrow front | 9-3/4 | 246 | Individual segment of the upper internal bay chain, left to right between adjacent frame/divider references. |
| Third divider | 1 | 25 | Individual segment of the upper internal bay chain, left to right between adjacent frame/divider references. |
| Right paired-door bay | 22-3/8 | 569 | Individual segment of the upper internal bay chain, left to right between adjacent frame/divider references. |
| Fourth divider | 1 | 25 | Individual segment of the upper internal bay chain, left to right between adjacent frame/divider references. |
| Right narrow front | 9-3/4 | 246 | Individual segment of the upper internal bay chain, left to right between adjacent frame/divider references. |
| Overall depth | 21-3/4 | 551 | Outer left vertical span across the full plan depth. |
| Rear-to-front inner reference depth | 20-7/8 | 531 | Right vertical span from rear outside reference to inset front reference. |
| Front projection depth | 3/4 | 20 | Short right vertical segment between the inset front reference and outside front edge. |
| Rear frame depth | 2 | 51 | Upper segment of the inner left vertical chain. |
| Inner depth between frame rails | 16-7/8 | 429 | Middle segment of the inner left depth chain. |
| Front frame depth | 2 | 51 | Lower segment of the inner left depth chain. |
| Lower left projection | 3/4 | 20 | Short lower horizontal span at the outer left side. |
| Lower left upright | 2 | 51 | Next lower horizontal segment to the inner left reference. |
| Lower inner width | 77-3/4 | 1976 | Repeated lower horizontal span between inner side references. |
| Lower right upright | 2 | 51 | Next lower segment toward the outside right reference. |
| Lower right projection | 3/4 | 20 | Short lower horizontal span at the outer right side. |
Source note: The source states: All measurements are plus or minus 1/4 inch. Values are copied as printed, not converted or approved for installation.
Source page 4: Cabinet back view
View original PDF — Source page 4: Cabinet back view
Original drawing: Cabinet back view.
Original source page 4, visually unchanged. Read this page's text equivalent.
View and dimensional relationships
The rear elevation shows two square cutouts in broad bays, with three narrow bays and intervening vertical framing. Individual chains locate rear frame spans and cutout sizes. The two outer 41 mm labels omit an inch counterpart. Square cutouts are not assigned a plumbing function beyond what the drawing depicts.
On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.
| Measurement | Inches | Millimeters | Reference points / meaning |
|---|---|---|---|
| Overall upper width | 83-1/4 | 2116 | Full outer width at top of the rear elevation. |
| Upper inner width | 77-3/4 | 1976 | Horizontal span between inner side-frame references. |
| Upper left projection | 3/4 | 20 | Left outer short horizontal reference. |
| Upper left upright | 2 | 51 | Left upper horizontal upright span. |
| Upper right upright | 2 | 51 | Right upper horizontal upright span. |
| Upper right projection | 3/4 | 20 | Right outer short horizontal reference. |
| Lower main width | 81-3/4 | 2078 | Bottom horizontal main span between inset outside references. |
| Lower left projection | 3/4 | 20 | Short lower left outer reference. |
| Lower right projection | 3/4 | 20 | Short lower right outer reference. |
| Overall rear height | 34 | 864 | Outer left vertical span from top to base bottom. |
| Left upper/body reference height | 29-1/4 | 744 | Left inner vertical segment from top to base reference. |
| Left base reference height | 4-3/4 | 122 | Left lower vertical segment from base reference to bottom. |
| Upper rear band height | 5-1/8 | 130 | Upper segment of the right vertical chain. |
| Main rear panel height | 23-1/4 | 589 | Second segment of the right vertical chain. |
| Lower rear rail height | 2-1/4 | 56 | Third segment of the right vertical chain. |
| Lower rear opening height | 3-5/8 | 91 | Lowest segment of the right vertical chain. |
| Left end reference | Not printed | 41 | Individual span of the internal horizontal rear bay/divider chain, left to right. End references show millimeters only where stated. |
| Left narrow bay | 7-7/8 | 201 | Individual span of the internal horizontal rear bay/divider chain, left to right. End references show millimeters only where stated. |
| First divider | 1-5/8 | 41 | Individual span of the internal horizontal rear bay/divider chain, left to right. End references show millimeters only where stated. |
| Left broad bay | 21 3/4 | 554 | Individual span of the internal horizontal rear bay/divider chain, left to right. End references show millimeters only where stated. |
| Second divider | 1-5/8 | 41 | Individual span of the internal horizontal rear bay/divider chain, left to right. End references show millimeters only where stated. |
| Center narrow bay | 9-1/8 | 231 | Individual span of the internal horizontal rear bay/divider chain, left to right. End references show millimeters only where stated. |
| Third divider | 1-5/8 | 41 | Individual span of the internal horizontal rear bay/divider chain, left to right. End references show millimeters only where stated. |
| Right broad bay | 21 3/4 | 554 | Individual span of the internal horizontal rear bay/divider chain, left to right. End references show millimeters only where stated. |
| Fourth divider | 1-5/8 | 41 | Individual span of the internal horizontal rear bay/divider chain, left to right. End references show millimeters only where stated. |
| Right narrow bay | 7-7/8 | 201 | Individual span of the internal horizontal rear bay/divider chain, left to right. End references show millimeters only where stated. |
| Right end reference | Not printed | 41 | Individual span of the internal horizontal rear bay/divider chain, left to right. End references show millimeters only where stated. |
| Left opening width | 7-7/8 | 201 | Horizontal span across the left square rear opening. |
| Left opening height | 7-7/8 | 201 | Vertical span across the left square rear opening. |
| Left opening upper offset | 4-1/4 | 107 | Vertical span from the upper panel/rail reference to the top of the left opening. |
| Right opening width | 7-7/8 | 201 | Horizontal span across the right square rear opening. |
| Right opening height | 7-7/8 | 201 | Vertical span across the right square rear opening. |
| Right opening upper offset | 4-1/4 | 107 | Vertical span from the upper panel/rail reference to the top of the right opening. |
| Left opening to inner right divider | 7 | 178 | Horizontal span from the left opening right edge to the indicated inner-right bay boundary. No corresponding right-opening offset is separately printed. |
Source note: The source states: All measurements are plus or minus 1/4 inch. Values are copied as printed, not converted or approved for installation.
Source note: Two outer 41 mm labels do not show an inch counterpart; the adjacent 1-5/8 inch /41 mm divider labels are separate. The two broad-bay inch labels visibly use a space:21 3/4.
Source page 5: Cabinet side view
View original PDF — Source page 5: Cabinet side view
Original drawing: Cabinet side view.
Original source page 5, visually unchanged. Read this page's text equivalent.
View and dimensional relationships
Side elevation shows a paneled cabinet side and shaped base. Front handles project at the left. The upper chain separately locates a small front offset, frame widths and side-panel span; the right chain locates upper band, panel height, lower rail and base. The overall base depth is separately printed below.
On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.
| Measurement | Inches | Millimeters | Reference points / meaning |
|---|---|---|---|
| Upper main depth span | 21-1/4 | 541 | Upper horizontal span from the inset front reference to the rear outside reference. |
| Front upright span | 2 | 51 | Individual segment of the upper depth chain, read from the front at left toward the rear at right. |
| Side panel horizontal span | 17-1/4 | 439 | Individual segment of the upper depth chain, read from the front at left toward the rear at right. |
| Rear upright span | 2 | 51 | Individual segment of the upper depth chain, read from the front at left toward the rear at right. |
| Upper front offset | 3/8 | 10 | Small horizontal distance between the outer front projection reference and the adjacent inset reference. |
| Overall side height | 34 | 864 | Outermost left vertical dimension from upper cabinet to lower base/floor reference. |
| Upper side band | 3 | 76 | Individual segment of the right-side vertical chain, read from top to bottom between adjacent references. |
| Side panel vertical span | 24-1/4 | 617 | Individual segment of the right-side vertical chain, read from top to bottom between adjacent references. |
| Lower side rail | 2 | 51 | Individual segment of the right-side vertical chain, read from top to bottom between adjacent references. |
| Side base span | 4-3/4 | 122 | Individual segment of the right-side vertical chain, read from top to bottom between adjacent references. |
| Lower outside depth | 21-3/4 | 551 | Full horizontal span between the outside front and rear base references below the elevation. |
Source note: The source states: All measurements are plus or minus 1/4 inch. Values are copied as printed, not converted or approved for installation.
Source page 6: 84 IN double-sink 2 IN Straight Mitered Edge countertop overview
View original PDF — Source page 6: 84 IN double-sink 2 IN Straight Mitered Edge countertop overview
Original drawing: 84 IN double-sink 2 IN Straight Mitered Edge countertop overview.
Original source page 6, visually unchanged. Read this page's text equivalent.
View and dimensional relationships
Perspective of a rectangular double-sink countertop with two rounded-corner sink openings, one faucet hole behind each, and a full rear backsplash. The title identifies 84 IN DOUBLE SINK 2 IN STRAIGHT MITERED EDGE. A deep straight edge is depicted. No dimension-line callouts occur on this overview.
No dimension callouts are printed on this overview page.
Source page 7: Straight-mitered countertop and backsplash
View original PDF — Source page 7: Straight-mitered countertop and backsplash
Original drawing: Straight-mitered countertop and backsplash.
Original source page 7, visually unchanged. Read this page's text equivalent.
View and dimensional relationships
Separate backsplash elevation and side profile sit above a long edge elevation. Below, the plan shows two rectangular rounded-corner sink openings, two faucet holes and eight bracket-hole symbols. Separate horizontal chains locate faucet axes, opening edges and bracket columns; vertical chains locate opening edges, faucet center and bracket rows. A narrow edge section appears at the right.
The title is 84 IN DOUBLE SINK 2 IN STRAIGHT MITERED EDGE COUNTERTOP. Two leaders identify 45 Degree Mitered Edge. The source limits these dimensions to Straight Mitered Edge and refers other styles to the Double Cove section.
On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.
| Measurement | Inches | Millimeters | Reference points / meaning |
|---|---|---|---|
| Backsplash length | 84 | 2134 | Full horizontal span of the separate backsplash elevation. |
| Backsplash height | 3-7/8 | 100 | Vertical span of the separate backsplash, not countertop profile height. |
| Backsplash thickness | 3/4 | 20 | Horizontal span of the narrow backsplash end view. |
| Front elevation profile height | 2 | 50 | Vertical profile-height dimension on the left of the front edge elevation. |
| Front elevation left return thickness | 3/4 | 20 | Separate short thickness dimension at the left end of the front elevation. |
| Front elevation right return thickness | 3/4 | 20 | Separate short thickness dimension at the right end of the front elevation. |
| Plan overall width | 84 | 2134 | Outside left-to-right span of the countertop in plan. |
| Left faucet-axis offset | 24-7/8 | 632 | Left outside edge to left faucet-hole centerline. |
| Faucet-axis spacing | 34-1/4 | 870 | Horizontal distance between the two faucet-hole centerlines. |
| Right faucet-axis offset | 24-7/8 | 632 | Right faucet-hole centerline to right outside edge. |
| Plan overall depth | 22 | 560 | Rear outside edge to front outside edge of the countertop. |
| Rear edge to sink opening | 5-1/2 | 140 | Upper segment of the left vertical chain, rear outside edge to rear edge of the left sink opening. |
| Sink opening depth | 12-1/4 | 310 | Middle segment of the left vertical chain across the opening from rear to front. |
| Sink opening to front edge | 4-3/8 | 110 | Lower segment of the left vertical chain, opening front edge to countertop front edge. |
| Rear edge to faucet center | 2-3/4 | 70 | Short vertical span near the left faucet hole, from the rear edge to its center. |
| Faucet-hole circular callout | 1-3/8 | 35 | Leader to the circular left faucet hole; the printed circular-hole size is preserved. |
| Rear edge to rear bracket row | 6-3/4 | 170 | Upper segment of the internal bracket-location chain from rear edge to rear bracket row. |
| Bracket-row separation | 9-7/8 | 250 | Middle segment between the rear and front bracket-location rows. |
| Front bracket row to front edge | 5-1/2 | 140 | Lower segment from front bracket row to outside front edge. |
| Left outside edge to left opening | 16-1/4 | 412 | First segment in the opening-edge chain beneath the plan. |
| Left sink opening width | 17-3/8 | 440 | Second segment across the left sink opening. |
| Solid span between openings | 16-7/8 | 430 | Middle segment between the inside edges of the two openings. |
| Right sink opening width | 17-3/8 | 440 | Fourth segment across the right sink opening. |
| Right opening to right outside edge | 16-1/4 | 412 | Last segment of the opening-edge chain. |
| Left outer bracket offset | 14 | 355 | Left outside edge to outer bracket column of the left sink. |
| Left bracket-column spacing | 21-3/4 | 554 | Horizontal spacing between bracket columns around the left sink. |
| Gap between inner bracket columns | 12-1/2 | 316 | Horizontal gap between the inner bracket columns of the two sinks. |
| Right bracket-column spacing | 21-3/4 | 554 | Horizontal spacing between bracket columns around the right sink. |
| Right outer bracket offset | 14 | 355 | Outer bracket column of the right sink to right outside edge. |
| Right side-profile height | 2 | 50 | Transverse span across the narrow right-hand profile view, independently repeated from the elevation. |
| Right profile upper thickness | 3/4 | 20 | Upper vertical thickness callout on the narrow right-hand profile view. |
| Right profile lower thickness | 3/4 | 20 | Lower vertical thickness callout on the narrow right-hand profile view. |
| Sink opening corner notation | Not printed | Not printed | Literal source notation 4-R10 with a leader to a rounded sink-opening corner. No unit is printed beside the notation, so no unit or conversion is invented. |
Source note: The source states: All measurements are plus or minus 1/4 inch. Values are copied as printed, not converted or approved for installation.
Source page 8: Standard rectangular undermount sink
View original PDF — Source page 8: Standard rectangular undermount sink
Original drawing: Standard rectangular undermount sink.
Original source page 8, visually unchanged. Read this page's text equivalent.
View and dimensional relationships
The left drawing shows the rectangular rim and the bowl inside it. The hatched band is outside the inner opening. Sloping walls run from that opening toward the bowl floor. Two unlabeled apertures are shown along the centerline; this page does not give their diameters.
The right drawing is a side section of the same sink. Its height label is a sectional outside measurement as drawn, not a separately labeled usable water depth. The countertop cutout dimensions appear on pages 7 and 10 and are different from the sink dimensions on this page.
On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.
| Measurement | Inches | Millimeters | Reference points / meaning |
|---|---|---|---|
| Outside rim width | 20-1/8 | 511 | Left-to-right span across the outside edges of the hatched rim. |
| Outside rim depth | 15 | 381 | Front-to-back span across the outside edges of the rim. |
| Inner opening width | 17-3/4 | 451 | Left-to-right span at the inner edge of the rim, above the sloping bowl walls. |
| Inner opening depth | 12-5/8 | 320.6 | Front-to-back span at the inner edge of the rim. |
| Section height | 7-5/8 | 193.6 | Vertical dimension of the side section, between the upper and lower reference lines shown. |
Source note: The source states: All measurements are +/- 1/4 inch. Values below are transcribed, not recalculated or approved for installation.
Source page 9: 84 IN double-sink 1.5 IN Double Cove Edge countertop overview
View original PDF — Source page 9: 84 IN double-sink 1.5 IN Double Cove Edge countertop overview
Original drawing: 84 IN double-sink 1.5 IN Double Cove Edge countertop overview.
Original source page 9, visually unchanged. Read this page's text equivalent.
View and dimensional relationships
Perspective of a rectangular double-sink countertop with two rounded-corner sink openings, one faucet hole behind each, and a full rear backsplash. The title identifies 84 IN DOUBLE SINK 1.5 IN DOUBLE COVE EDGE. Layered molded front, side edges and backsplash are depicted. No dimension-line callouts occur on this overview.
No dimension callouts are printed on this overview page.
Source page 10: Double-cove countertop and backsplash
View original PDF — Source page 10: Double-cove countertop and backsplash
Original drawing: Double-cove countertop and backsplash.
Original source page 10, visually unchanged. Read this page's text equivalent.
View and dimensional relationships
Separate backsplash elevation and side profile sit above a long edge elevation. Below, the plan shows two rectangular rounded-corner sink openings, two faucet holes and eight bracket-hole symbols. Separate horizontal chains locate faucet axes, opening edges and bracket columns; vertical chains locate opening edges, faucet center and bracket rows. A narrow edge section appears at the right.
The title is 84 IN DOUBLE SINK 1.5 IN DOUBLE COVE EDGE COUNTERTOP. Detailed profile labels separately print 1-5/8 inch /40 mm. The source limits these dimensions to Double Cove Edge and refers other styles to the Straight Mitered section. The rear inset literally reads 1/1 inch /25 mm; its intended wording remains unconfirmed.
On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.
| Measurement | Inches | Millimeters | Reference points / meaning |
|---|---|---|---|
| Backsplash length | 81-7/8 | 2080 | Full horizontal span of the separate backsplash elevation. |
| Backsplash height | 3-7/8 | 100 | Vertical span of the separate backsplash, not countertop profile height. |
| Backsplash thickness | 3/4 | 20 | Horizontal span of the narrow backsplash end view. |
| Front elevation profile height | 1-5/8 | 40 | Vertical profile-height dimension on the left of the front edge elevation. |
| Front elevation layer 1 | 3/4 | 20 | Separate upper layer thickness at the right of the front elevation. |
| Front elevation layer 2 | 3/4 | 20 | Separate lower layer thickness at the right of the front elevation. |
| Plan overall width | 84 | 2134 | Outside left-to-right span of the countertop in plan. |
| Left faucet-axis offset | 24-7/8 | 632 | Left outside edge to left faucet-hole centerline. |
| Faucet-axis spacing | 34-1/4 | 870 | Horizontal distance between the two faucet-hole centerlines. |
| Right faucet-axis offset | 24-7/8 | 632 | Right faucet-hole centerline to right outside edge. |
| Plan overall depth | 22 | 560 | Rear outside edge to front outside edge of the countertop. |
| Rear edge to sink opening | 5-1/2 | 140 | Upper segment of the left vertical chain, rear outside edge to rear edge of the left sink opening. |
| Sink opening depth | 12-1/4 | 310 | Middle segment of the left vertical chain across the opening from rear to front. |
| Sink opening to front edge | 4-3/8 | 110 | Lower segment of the left vertical chain, opening front edge to countertop front edge. |
| Rear edge to faucet center | 2-3/4 | 70 | Short vertical span near the left faucet hole, from the rear edge to its center. |
| Faucet-hole circular callout | 1-3/8 | 35 | Leader to the circular left faucet hole; the printed circular-hole size is preserved. |
| Rear edge to rear bracket row | 6-3/4 | 170 | Upper segment of the internal bracket-location chain from rear edge to rear bracket row. |
| Bracket-row separation | 9-7/8 | 250 | Middle segment between the rear and front bracket-location rows. |
| Front bracket row to front edge | 5-1/2 | 140 | Lower segment from front bracket row to outside front edge. |
| Left outside edge to left opening | 16-1/4 | 412 | First segment in the opening-edge chain beneath the plan. |
| Left sink opening width | 17-3/8 | 440 | Second segment across the left sink opening. |
| Solid span between openings | 16-7/8 | 430 | Middle segment between the inside edges of the two openings. |
| Right sink opening width | 17-3/8 | 440 | Fourth segment across the right sink opening. |
| Right opening to right outside edge | 16-1/4 | 412 | Last segment of the opening-edge chain. |
| Left outer bracket offset | 14 | 355 | Left outside edge to outer bracket column of the left sink. |
| Left bracket-column spacing | 21-3/4 | 554 | Horizontal spacing between bracket columns around the left sink. |
| Gap between inner bracket columns | 12-1/2 | 316 | Horizontal gap between the inner bracket columns of the two sinks. |
| Right bracket-column spacing | 21-3/4 | 554 | Horizontal spacing between bracket columns around the right sink. |
| Right outer bracket offset | 14 | 355 | Outer bracket column of the right sink to right outside edge. |
| Right side-profile height | 1-5/8 | 40 | Transverse span across the narrow right-hand profile view, independently repeated from the elevation. |
| Rear inner-border offset | 1/1 | 25 | Small vertical rear-edge to dashed-inner-line dimension at the top-right of the plan. Literal unusual fraction retained.Unresolved: CH84-P10-REAR |
| Right inner-border offset | 2 | 50 | Short horizontal span between the right outside edge and nearby dashed inner reference. |
| Front inner-border offset | 2 | 50 | Short vertical span between the front outside edge and nearby dashed inner reference. |
| Sink opening corner notation | Not printed | Not printed | Literal source notation 4-R20 with a leader to a rounded sink-opening corner. No unit is printed beside the notation, so no unit or conversion is invented. |
Source note: The source states: All measurements are plus or minus 1/4 inch. Values are copied as printed, not converted or approved for installation.
Source and assistance
View the original source PDF. Source reviewed 19 November 2026.
Request an accessible format or a confirmed drawing, or call Willow Bath and Vanity at (877) 788-8444.