Wishlist

Madison Teak Floating 24 vanity - drawing text version

Madison Teak Floating 24 vanity - source drawing text version

This is a text version of the source drawings. Original drawing images are available through the PDF page links below. Keep the source notes and limitations in mind when using this text version.

Text version of the source drawing

All printed dimension labels are preserved without engineering approval. Obtain confirmed dimensions from Willow Bath and Vanity before installation, fabrication, or drilling.

Text equivalent of all ten source pages. Printed dimensions and alternative countertop styles are preserved separately; no engineering approval or conversion is supplied.

Each source page has its original drawing, a description of the view, and a table identifying what each dimension measures. Inches and millimeters are copied independently from the source; no conversion replaces a printed value.

Source limitations

Inches and millimeters remain separately printed source values. The source does not establish the controlling unit, current approval or included accessories.

The cabinet depth is 21-1/2 in /546 mm in the top view and 21-1/2 in /545 mm in the side view. Both labels remain unchanged.

The Double Cove title says 1.5 IN; its detailed edge is labeled 1-5/8 in /40 mm. No nominal-versus-actual interpretation is inferred.

Source page 1: Madison Teak Floating 24 cabinet overview

View original PDF — Source page 1: Madison Teak Floating 24 cabinet overview

Original drawing: Madison Teak Floating 24 cabinet overview.

Original source page 1, visually unchanged. Read this page's text equivalent.

View and dimensional relationships

Perspective drawing of an open-top rectangular cabinet without legs. Two broad drawer fronts are framed by stiles and rails. A U-shaped recess is visible in the upper interior drawer and a rectangular opening is visible at the rear. This view shows no countertop or separate dimension callouts.

The source title reads MADISON TEAK FLOATING 24 IN SINGLE SINK BATHROOM VANITY. Footer: willowbathandvanity.com; info@willowbathandvanity.com; 1-877-788-8444.

No dimension callouts are printed on this overview page.

Back to contents

Source page 2: Cabinet front view

View original PDF — Source page 2: Cabinet front view

Original drawing: Cabinet front view.

Original source page 2, visually unchanged. Read this page's text equivalent.

View and dimensional relationships

Two stacked wide drawer fronts sit between narrow side stiles. The left vertical chain separately labels the top rail, gaps, drawer fronts and bottom rail. Bottom dimensions distinguish the inner front width from the two side widths.

On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.

Page 2 dimensions, as printed
Measurement Inches Millimeters Reference points / meaning
Overall cabinet width 23 585 Full outside horizontal span above the elevation.
Overall cabinet height 21 533 Full vertical outside span at the right of the elevation.
Top rail height 1 25 First upper segment of the left vertical chain.
Gap below top rail 3/4 20 Short segment between the top rail and upper drawer front.
Upper drawer front height 8-3/4 221 Vertical span of the upper broad front.
Gap between drawer fronts 3/4 20 Short middle segment between the upper and lower fronts.
Lower drawer front height 8-3/4 221 Vertical span of the lower broad front.
Bottom rail height 1 25 Lower segment from the lower front to the cabinet bottom.
Inner front width 21 533 Bottom horizontal span between the inner edges of the left and right stiles.
Left side stile width 1 25 Bottom left short horizontal segment.
Right side stile width 1 25 Bottom right short horizontal segment.

Source note: The source states: All measurements are plus or minus 1/4 inch. Values remain as printed, not converted or approved for installation.

Back to contents

Source page 3: Cabinet top view

View original PDF — Source page 3: Cabinet top view

Original drawing: Cabinet top view.

Original source page 3, visually unchanged. Read this page's text equivalent.

View and dimensional relationships

A rectangular outer frame surrounds a U-shaped interior drawer recess. The upper horizontal label measures the complete cabinet; the lower chain measures the inner bay and side widths. Left dimensions divide the outside depth; the central labels describe the U-shaped recess.

On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.

Page 3 dimensions, as printed
Measurement Inches Millimeters Reference points / meaning
Overall cabinet width 23 585 Full outside horizontal span above the plan.
Overall cabinet depth 21-1/2 546 Full outside vertical span at the right of the plan.
Rear rail depth 2 50 Upper segment of the left vertical chain.
Inner depth span 17-1/8 435 Middle segment of the left vertical chain.
Front rail depth 2-3/8 60 Lower segment of the left vertical chain.
Inner bay width 21 533 Lower horizontal span between inner side references.
Left side width 1 25 Lower left short horizontal span.
Right side width 1 25 Lower right short horizontal span.
U-shaped recess width 4-3/4 119 Horizontal span across the central recess between its vertical inner edges.
U-shaped recess depth 9-5/8 244 Vertical span from the upper recess reference to its lower inside end.

Source note: The source states: All measurements are plus or minus 1/4 inch. Values remain as printed, not converted or approved for installation.

Back to contents

Source page 4: Cabinet back view

View original PDF — Source page 4: Cabinet back view

Original drawing: Cabinet back view.

Original source page 4, visually unchanged. Read this page's text equivalent.

View and dimensional relationships

The upper mounting region has two horizontal bracket sections with rows of round fastener holes; the BRACKET leader points to the right section. A rectangular opening lies in the lower rear panel. Dimensions refer separately to the outer frame, bracket region, opening and inset panel side strips; no hole diameters or mounting fastener specification are printed.

On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.

Page 4 dimensions, as printed
Measurement Inches Millimeters Reference points / meaning
Inner rear width 21 533 Upper horizontal span between the inner side-stile references.
Left outside stile width 1 25 Upper left short horizontal span.
Right outside stile width 1 25 Upper right short horizontal span.
Overall cabinet height 21 533 Full outside vertical span at the left.
Top rail height 1 25 Upper right short vertical span.
Upper bracket region height 4 102 Right vertical span from below the top rail to the bottom of the upper mounting region.
Upper region to opening top 4-1/2 114 Vertical offset from the bottom of the upper mounting region to the rectangular opening top.
Rear opening height 5-7/8 150 Vertical span at the left of the rectangular opening.
Rear opening width 5-7/8 150 Horizontal span below the rectangular opening.
Opening to right inner panel reference 6 152 Horizontal span from the opening right edge to the indicated inner right panel line.
Left inset panel strip width 1-5/8 41 Lower left horizontal span from the inner stile reference to the inset panel line.
Right inset panel strip width 1-5/8 41 Lower right horizontal span between the inset panel line and inner stile reference.

Source note: The source states: All measurements are plus or minus 1/4 inch. Values remain as printed, not converted or approved for installation.

Back to contents

Source page 5: Cabinet side view

View original PDF — Source page 5: Cabinet side view

Original drawing: Cabinet side view.

Original source page 5, visually unchanged. Read this page's text equivalent.

View and dimensional relationships

The side panel is enclosed by upper and lower rails and two vertical end members. The elevation contains an outside depth and height, an internal panel height and a bottom horizontal chain. The top view separately prints a 546 mm depth; this side view prints 545 mm.

On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.

Page 5 dimensions, as printed
Measurement Inches Millimeters Reference points / meaning
Overall cabinet depth 21-1/2 545 Full outside horizontal span above the side elevation.
Overall cabinet height 21 533 Full outside vertical span on the left.
Upper side rail height 2 51 Upper segment of the right vertical chain.
Inner side panel height 17 432 Middle segment of the right vertical chain.
Lower side rail height 2 51 Lower segment of the right vertical chain.
Left end member depth 2-3/8 60 Left segment of the bottom horizontal chain.
Inner side panel depth 17-1/8 435 Middle segment of the bottom horizontal chain.
Right end member depth 2 51 Right segment of the bottom horizontal chain.

Source note: The source states: All measurements are plus or minus 1/4 inch. Values remain as printed, not converted or approved for installation.

Back to contents

Source page 6: 24 inch Straight Mitered Edge countertop overview

View original PDF — Source page 6: 24 inch Straight Mitered Edge countertop overview

Original drawing: 24 inch Straight Mitered Edge countertop overview.

Original source page 6, visually unchanged. Read this page's text equivalent.

View and dimensional relationships

Perspective drawing of a rectangular countertop with one central rounded rectangular sink opening, one round faucet hole behind the opening, a flat rear backsplash and a straight front/side edge. The title identifies 24 IN SINGLE SINK 2 IN STRAIGHT MITERED EDGE COUNTERTOP; this overview has no separate dimension callouts.

No dimension callouts are printed on this overview page.

Back to contents

Source page 7: Straight Mitered Edge countertop dimensions

View original PDF — Source page 7: Straight Mitered Edge countertop dimensions

Original drawing: Straight Mitered Edge countertop dimensions.

Original source page 7, visually unchanged. Read this page's text equivalent.

View and dimensional relationships

Separate backsplash front and side elevations appear above the straight edge elevation. Below, a top plan locates the single opening and faucet hole; a narrow edge section appears on the right. Two leaders state 45 Degree Mitered Edge. The source note says these dimensions apply exclusively to Straight Mitered Edge countertops and refers the other style to the Double Cove Edge section.

On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.

Page 7 dimensions, as printed
Measurement Inches Millimeters Reference points / meaning
Backsplash width 24 610 Horizontal full span of the backsplash elevation.
Backsplash height 3-7/8 100 Vertical span at the left of the backsplash elevation.
Backsplash thickness 3/4 20 Horizontal thickness of the separate side profile.
Mitered edge height 2 50 Full vertical span of the front edge elevation.
Left edge wall thickness 3/4 20 Short horizontal inset at the left end of the front edge elevation.
Right edge wall thickness 3/4 20 Short horizontal inset at the right end of the front edge elevation.
Plan outside width 24 610 Full horizontal outside span of the countertop.
Left edge to faucet center 12 305 Upper left horizontal segment to the faucet centerline.
Faucet center to right edge 12 305 Upper right horizontal segment from the faucet centerline.
Plan outside depth 22 560 Full vertical outside span on the left.
Rear edge to sink opening 5-1/2 140 Upper segment of the left opening chain.
Sink opening depth 10 255 Middle segment of the left opening chain.
Sink opening to front edge 6-1/2 165 Lower segment of the left opening chain.
Rear edge to faucet center 2-3/4 70 Short vertical span to the round faucet hole center.
Faucet-hole diameter 1-3/8 35 Diameter leader attached to the round faucet hole.
Left edge to sink opening 4-3/8 112.5 Left segment of the bottom horizontal opening chain.
Sink opening width 15-1/8 385 Middle segment of the bottom horizontal opening chain.
Sink opening to right edge 4-3/8 112.5 Right segment of the bottom horizontal opening chain.
Separate edge section width 2 50 Horizontal span across the narrow right edge section.
Separate edge section upper wall 3/4 20 Short vertical segment at the upper end of the right edge section.
Separate edge section lower wall 3/4 20 Short vertical segment at the lower end of the right edge section.

Source note: The source states: All measurements are plus or minus 1/4 inch. Values remain as printed, not converted or approved for installation.

Back to contents

Source page 8: Standard rectangular undermount sink

View original PDF — Source page 8: Standard rectangular undermount sink

Original drawing: Standard rectangular undermount sink.

Original source page 8, visually unchanged. Read this page's text equivalent.

View and dimensional relationships

The left drawing shows the rectangular rim and the bowl inside it. The hatched band is outside the inner opening. Sloping walls run from that opening toward the bowl floor. Two unlabeled apertures are shown along the centerline; this page does not give their diameters.

The right drawing is a side section of the same sink. Its height label is a sectional outside measurement as drawn, not a separately labeled usable water depth. The countertop cutout dimensions appear on pages 7 and 10 and are different from the sink dimensions on this page.

On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.

Page 8 dimensions, as printed
Measurement Inches Millimeters Reference points / meaning
Outside rim width 20-1/8 511 Left-to-right span across the outside edges of the hatched rim.
Outside rim depth 15 381 Front-to-back span across the outside edges of the rim.
Inner opening width 17-3/4 451 Left-to-right span at the inner edge of the rim, above the sloping bowl walls.
Inner opening depth 12-5/8 320.6 Front-to-back span at the inner edge of the rim.
Section height 7-5/8 193.6 Vertical dimension of the side section, between the upper and lower reference lines shown.

Source note: The source states: All measurements are +/- 1/4 inch. Values below are transcribed, not recalculated or approved for installation.

Back to contents

Source page 9: 24 inch Double Cove Edge countertop overview

View original PDF — Source page 9: 24 inch Double Cove Edge countertop overview

Original drawing: 24 inch Double Cove Edge countertop overview.

Original source page 9, visually unchanged. Read this page's text equivalent.

View and dimensional relationships

Perspective drawing of a single-opening countertop with a round faucet hole and a shaped rear backsplash. The front and side edges have a stepped molded profile. Title: 24 IN SINGLE SINK 1.5 IN DOUBLE COVE EDGE COUNTERTOP. No separate dimension callouts appear on this overview.

No dimension callouts are printed on this overview page.

Back to contents

Source page 10: Double Cove Edge countertop dimensions

View original PDF — Source page 10: Double Cove Edge countertop dimensions

Original drawing: Double Cove Edge countertop dimensions.

Original source page 10, visually unchanged. Read this page's text equivalent.

View and dimensional relationships

The upper drawings show a molded backsplash front and side profile and a layered edge elevation. A plan below locates the single sink opening and faucet hole, with inset rear, side and front bands. A separate narrow edge section is at the right. The source note restricts these dimensions to Double Cove Edge countertops and refers the other style to the Straight Mitered Edge section.

The title says 1.5 IN while the detailed edge height is 1-5/8 in /40 mm. These are retained as separate printed labels without an engineering ruling.

On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.

Page 10 dimensions, as printed
Measurement Inches Millimeters Reference points / meaning
Backsplash width 21-7/8 556 Horizontal full span of the molded backsplash elevation.
Backsplash height 3-7/8 100 Vertical height of the molded backsplash elevation.
Backsplash thickness 3/4 20 Horizontal thickness of the separate side profile.
Cove edge height 1-5/8 40 Full vertical span of the layered edge elevation.
Cove edge upper segment 3/4 20 Upper short vertical segment at the right end of the edge elevation.
Cove edge lower segment 3/4 20 Lower short vertical segment at the right end of the edge elevation.
Plan outside width 24 610 Full horizontal outside span of the countertop.
Left edge to faucet center 12 305 Upper left horizontal segment to the faucet centerline.
Faucet center to right edge 12 305 Upper right horizontal segment from the faucet centerline.
Plan outside depth 22 560 Full vertical outside span on the left.
Rear edge to sink opening 5-1/2 140 Upper segment of the left opening chain.
Sink opening depth 10 255 Middle segment of the left opening chain.
Sink opening to front edge 6-1/2 165 Lower segment of the left opening chain.
Rear edge to faucet center 2-3/4 70 Short vertical span to the round faucet hole center.
Faucet-hole diameter 1-3/8 35 Diameter leader attached to the round faucet hole.
Left edge to sink opening 4-3/8 112.5 Left segment of the bottom horizontal opening chain.
Sink opening width 15-1/8 385 Middle segment of the bottom horizontal opening chain.
Sink opening to right edge 4-3/8 112.5 Right segment of the bottom horizontal opening chain.
Rear inset band 1 25 Short vertical distance from rear outside edge to rear dashed inset line.
Right inset band 2 50 Short horizontal distance across the right band in the plan.
Front inset band 2 50 Short vertical distance across the lower band in the plan.
Separate edge section width 1-5/8 40 Horizontal span above the narrow right edge section.

Source note: The source states: All measurements are plus or minus 1/4 inch. Values remain as printed, not converted or approved for installation.

Back to contents

Source and assistance

View the original source PDF. Source reviewed 19 November 2026.

Request an accessible format or a confirmed drawing, or call Willow Bath and Vanity at (877) 788-8444.

Updated 19 November 2026. This text version explains the source drawing; it is not a new installation specification.