Parker 84 double sink vanity - drawing text version
Parker 84 double-sink vanity - source drawing text version
PDF with text descriptions — 23 pages.
This is a text version of the source drawings. Original drawing images are available through the PDF page links below. Keep the source warnings and unresolved dimensions in mind when using this text version.
All printed dimension labels are preserved without engineering approval. Obtain confirmed dimensions from Willow Bath and Vanity before installation, fabrication, or drilling.
Text companion to all ten original pages, preserving printed cabinet, countertop and sink references separately. No engineering dimensions or accessory inclusion are inferred or approved.
Each source page has its original drawing, a description of the view, and a table identifying what each dimension measures. Inches and millimeters are copied independently from the source; no conversion replaces a printed value.
Source limitations
Cabinet, countertop and sink views are described separately for this source.
Source dimensions are retained as printed, without computing omitted dimensions or treating one measurement unit as controlling.
PK84-P10-REAR - source page 10
Unusual printed rear inner-border fraction: 1/1 in / 25 mm.
The original rear inset callout visibly prints 1/1 inch alongside 25 mm. The unusual fraction is preserved literally; it has not been silently normalized or replaced.
Confirm the intended inch label and reference offset with Willow Bath and Vanity before installation. No correction has been made.
Source page 1: Parker 84 double-sink cabinet overview
View original PDF — Source page 1: Parker 84 double-sink cabinet overview
Original drawing: Parker 84 double-sink cabinet overview.
Original source page 1, visually unchanged. Read this page's text equivalent.
View and dimensional relationships
Perspective of an open-top cabinet on corner legs and a center support. Five front columns alternate narrow and broad widths; each has two stacked fronts. Open lower compartments contain slatted shelving. Internal drawer boxes, U-shaped clearances in broad bays, dividers and frame supports are visible. No countertop is shown. The source title identifies PARKER 84 IN DOUBLE SINK BATHROOM VANITY; no dimension callouts occur here.
Source branding: Willow Bath and Vanity. Footer contact: willowbathandvanity.com; info@willowbathandvanity.com;1-877-788-8444.
No dimension callouts are printed on this overview page.
Source page 2: Cabinet front view
View original PDF — Source page 2: Cabinet front view
Original drawing: Cabinet front view.
Original source page 2, visually unchanged. Read this page's text equivalent.
View and dimensional relationships
Five front columns alternate narrow and broad spans, each with two stacked fronts. An open lower compartment and a lower shelf/rail are shown, with a center supporting leg. Two handle-hole spacing labels are printed only on the center column.
On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.
| Measurement | Inches | Millimeters | Reference points / meaning |
|---|---|---|---|
| Overall front width | 83-1/4 | 2114 | Full outside horizontal span of the cabinet front. |
| Left narrow front width | 12 | 304 | Separate upper horizontal span across the named front, between its side references. Divider widths are not separately labeled. |
| Left wide front width | 20-1/8 | 511 | Separate upper horizontal span across the named front, between its side references. Divider widths are not separately labeled. |
| Center narrow front width | 12 | 304 | Separate upper horizontal span across the named front, between its side references. Divider widths are not separately labeled. |
| Right wide front width | 20-1/8 | 511 | Separate upper horizontal span across the named front, between its side references. Divider widths are not separately labeled. |
| Right narrow front width | 12 | 304 | Separate upper horizontal span across the named front, between its side references. Divider widths are not separately labeled. |
| Overall cabinet height | 33-1/2 | 850 | Outer left vertical span from cabinet top to the lower foot reference. |
| Upper front height | 7-1/2 | 190 | Upper short left vertical span across the first row of fronts. |
| Lower front height | 7-1/2 | 190 | Second short left vertical span across the second row of fronts. |
| Open lower compartment height | 9 | 230 | Vertical clear span below the main front rail to the top of the lower shelf/rail reference. |
| Lower foot reference span | 4 | 100 | Vertical span from underside of the lower shelf/rail to the foot-bottom reference. |
| Upper center handle-hole spacing | 5 | 128 | Horizontal center-to-center spacing between the two marked holes in the upper center front. |
| Lower center handle-hole spacing | 5 | 128 | Repeated center-to-center spacing between the two marked holes in the lower center front. |
Source note: The source states: All measurements are plus or minus 1/4 inch. Values are copied as printed, not converted or approved for installation.
Source page 3: Cabinet top view
View original PDF — Source page 3: Cabinet top view
Original drawing: Cabinet top view.
Original source page 3, visually unchanged. Read this page's text equivalent.
View and dimensional relationships
The open top plan shows five inner compartments. The two broad compartments have U-shaped drawer clearance regions; the three narrow compartments are rectangular. Frame rails, dividers and corner reinforcement are visible. The three printed dimensions identify full width, full depth and center drawer depth.
On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.
| Measurement | Inches | Millimeters | Reference points / meaning |
|---|---|---|---|
| Overall cabinet width | 83-1/4 | 2114 | Full horizontal width between the outside left and right references. |
| Overall cabinet depth | 21-5/8 | 550 | Full vertical front-to-back span of the cabinet plan. |
| Center drawer depth | 16 | 410 | Vertical front-to-back reference within the central narrow drawer box. |
Source note: The source states: All measurements are plus or minus 1/4 inch. Values are copied as printed, not converted or approved for installation.
Source page 4: Cabinet back view
View original PDF — Source page 4: Cabinet back view
Original drawing: Cabinet back view.
Original source page 4, visually unchanged. Read this page's text equivalent.
View and dimensional relationships
The rear view shows a long rectangular band subdivided by four vertical lines, above the open lower compartment and shelf/rail. The upper horizontal chain preserves the five rear spans as drawn; the vertical chain locates the band relative to the cabinet top and feet. No additional opening diameter, function or missing dimension is inferred.
On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.
| Measurement | Inches | Millimeters | Reference points / meaning |
|---|---|---|---|
| Overall rear width | 83-1/4 | 2114 | Full outside horizontal span above the rear elevation. |
| Left outer span | 20-1/2 | 520 | Individual segment of the upper rear horizontal chain, left to right between adjacent indicated vertical references. |
| Left narrow rear span | 8-5/8 | 220 | Individual segment of the upper rear horizontal chain, left to right between adjacent indicated vertical references. |
| Middle rear span | 25 | 634 | Individual segment of the upper rear horizontal chain, left to right between adjacent indicated vertical references. |
| Right narrow rear span | 8-5/8 | 220 | Individual segment of the upper rear horizontal chain, left to right between adjacent indicated vertical references. |
| Right outer span | 20-1/2 | 520 | Individual segment of the upper rear horizontal chain, left to right between adjacent indicated vertical references. |
| Top to rear band upper edge | 3-1/8 | 80 | Upper left vertical segment from cabinet top to the upper edge of the rectangular rear band. |
| Rear band vertical span | 13 | 330 | Middle left vertical segment between upper and lower edges of the rear band. |
| Rear band bottom to lower reference | 17-3/8 | 440 | Lower left vertical segment from bottom of the rear band to the lower foot reference. |
Source note: The source states: All measurements are plus or minus 1/4 inch. Values are copied as printed, not converted or approved for installation.
Source page 5: Cabinet side view
View original PDF — Source page 5: Cabinet side view
Original drawing: Cabinet side view.
Original source page 5, visually unchanged. Read this page's text equivalent.
View and dimensional relationships
Side elevation shows two dashed internal drawer-box sections above an open lower region and a lower shelf/rail. The upper drawer includes a recessed internal outline. Only overall depth and two drawer-box height references are labeled.
On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.
| Measurement | Inches | Millimeters | Reference points / meaning |
|---|---|---|---|
| Overall cabinet depth | 21-5/8 | 550 | Upper horizontal span from rear outside reference at left to front outside reference at right. |
| Upper drawer-box height | 3-3/4 | 96 | Short upper vertical reference across the upper dashed drawer-box section. |
| Lower drawer-box height | 3-3/4 | 96 | Short lower vertical reference across the lower dashed drawer-box section. |
Source note: The source states: All measurements are plus or minus 1/4 inch. Values are copied as printed, not converted or approved for installation.
Source page 6: 84 IN double-sink 2 IN Straight Mitered Edge countertop overview
View original PDF — Source page 6: 84 IN double-sink 2 IN Straight Mitered Edge countertop overview
Original drawing: 84 IN double-sink 2 IN Straight Mitered Edge countertop overview.
Original source page 6, visually unchanged. Read this page's text equivalent.
View and dimensional relationships
Perspective of a rectangular double-sink countertop with two rounded-corner sink openings, one faucet hole behind each, and a full rear backsplash. The title identifies 84 IN DOUBLE SINK 2 IN STRAIGHT MITERED EDGE. A deep straight edge is depicted. No dimension-line callouts occur on this overview.
No dimension callouts are printed on this overview page.
Source page 7: Straight-mitered countertop and backsplash
View original PDF — Source page 7: Straight-mitered countertop and backsplash
Original drawing: Straight-mitered countertop and backsplash.
Original source page 7, visually unchanged. Read this page's text equivalent.
View and dimensional relationships
Separate backsplash elevation and side profile sit above a long edge elevation. Below, the plan shows two rectangular rounded-corner sink openings, two faucet holes and eight bracket-hole symbols. Separate horizontal chains locate faucet axes, opening edges and bracket columns; vertical chains locate opening edges, faucet center and bracket rows. A narrow edge section appears at the right.
The title is 84 IN DOUBLE SINK 2 IN STRAIGHT MITERED EDGE COUNTERTOP. Two leaders identify 45 Degree Mitered Edge. The source limits these dimensions to Straight Mitered Edge and refers other styles to the Double Cove section.
On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.
| Measurement | Inches | Millimeters | Reference points / meaning |
|---|---|---|---|
| Backsplash length | 84 | 2134 | Full horizontal span of the separate backsplash elevation. |
| Backsplash height | 3-7/8 | 100 | Vertical span of the separate backsplash, not countertop profile height. |
| Backsplash thickness | 3/4 | 20 | Horizontal span of the narrow backsplash end view. |
| Front elevation profile height | 2 | 50 | Vertical profile-height dimension on the left of the front edge elevation. |
| Front elevation left return thickness | 3/4 | 20 | Separate short thickness dimension at the left end of the front elevation. |
| Front elevation right return thickness | 3/4 | 20 | Separate short thickness dimension at the right end of the front elevation. |
| Plan overall width | 84 | 2134 | Outside left-to-right span of the countertop in plan. |
| Left faucet-axis offset | 24-7/8 | 632 | Left outside edge to left faucet-hole centerline. |
| Faucet-axis spacing | 34-1/4 | 870 | Horizontal distance between the two faucet-hole centerlines. |
| Right faucet-axis offset | 24-7/8 | 632 | Right faucet-hole centerline to right outside edge. |
| Plan overall depth | 22 | 560 | Rear outside edge to front outside edge of the countertop. |
| Rear edge to sink opening | 5-1/2 | 140 | Upper segment of the left vertical chain, rear outside edge to rear edge of the left sink opening. |
| Sink opening depth | 12-1/4 | 310 | Middle segment of the left vertical chain across the opening from rear to front. |
| Sink opening to front edge | 4-3/8 | 110 | Lower segment of the left vertical chain, opening front edge to countertop front edge. |
| Rear edge to faucet center | 2-3/4 | 70 | Short vertical span near the left faucet hole, from the rear edge to its center. |
| Faucet-hole circular callout | 1-3/8 | 35 | Leader to the circular left faucet hole; the printed circular-hole size is preserved. |
| Rear edge to rear bracket row | 6-3/4 | 170 | Upper segment of the internal bracket-location chain from rear edge to rear bracket row. |
| Bracket-row separation | 9-7/8 | 250 | Middle segment between the rear and front bracket-location rows. |
| Front bracket row to front edge | 5-1/2 | 140 | Lower segment from front bracket row to outside front edge. |
| Left outside edge to left opening | 16-1/4 | 412 | First segment in the opening-edge chain beneath the plan. |
| Left sink opening width | 17-3/8 | 440 | Second segment across the left sink opening. |
| Solid span between openings | 16-7/8 | 430 | Middle segment between the inside edges of the two openings. |
| Right sink opening width | 17-3/8 | 440 | Fourth segment across the right sink opening. |
| Right opening to right outside edge | 16-1/4 | 412 | Last segment of the opening-edge chain. |
| Left outer bracket offset | 14 | 355 | Left outside edge to outer bracket column of the left sink. |
| Left bracket-column spacing | 21-3/4 | 554 | Horizontal spacing between bracket columns around the left sink. |
| Gap between inner bracket columns | 12-1/2 | 316 | Horizontal gap between the inner bracket columns of the two sinks. |
| Right bracket-column spacing | 21-3/4 | 554 | Horizontal spacing between bracket columns around the right sink. |
| Right outer bracket offset | 14 | 355 | Outer bracket column of the right sink to right outside edge. |
| Right side-profile height | 2 | 50 | Transverse span across the narrow right-hand profile view, independently repeated from the elevation. |
| Right profile upper thickness | 3/4 | 20 | Upper vertical thickness callout on the narrow right-hand profile view. |
| Right profile lower thickness | 3/4 | 20 | Lower vertical thickness callout on the narrow right-hand profile view. |
| Sink opening corner notation | Not printed | Not printed | Literal source notation 4-R10 with a leader to a rounded sink-opening corner. No unit is printed beside the notation, so no unit or conversion is invented. |
Source note: The source states: All measurements are plus or minus 1/4 inch. Values are copied as printed, not converted or approved for installation.
Source page 8: Standard rectangular undermount sink
View original PDF — Source page 8: Standard rectangular undermount sink
Original drawing: Standard rectangular undermount sink.
Original source page 8, visually unchanged. Read this page's text equivalent.
View and dimensional relationships
The left drawing shows the rectangular rim and the bowl inside it. The hatched band is outside the inner opening. Sloping walls run from that opening toward the bowl floor. Two unlabeled apertures are shown along the centerline; this page does not give their diameters.
The right drawing is a side section of the same sink. Its height label is a sectional outside measurement as drawn, not a separately labeled usable water depth. The countertop cutout dimensions appear on pages 7 and 10 and are different from the sink dimensions on this page.
On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.
| Measurement | Inches | Millimeters | Reference points / meaning |
|---|---|---|---|
| Outside rim width | 20-1/8 | 511 | Left-to-right span across the outside edges of the hatched rim. |
| Outside rim depth | 15 | 381 | Front-to-back span across the outside edges of the rim. |
| Inner opening width | 17-3/4 | 451 | Left-to-right span at the inner edge of the rim, above the sloping bowl walls. |
| Inner opening depth | 12-5/8 | 320.6 | Front-to-back span at the inner edge of the rim. |
| Section height | 7-5/8 | 193.6 | Vertical dimension of the side section, between the upper and lower reference lines shown. |
Source note: The source states: All measurements are +/- 1/4 inch. Values below are transcribed, not recalculated or approved for installation.
Source page 9: 84 IN double-sink 1.5 IN Double Cove Edge countertop overview
View original PDF — Source page 9: 84 IN double-sink 1.5 IN Double Cove Edge countertop overview
Original drawing: 84 IN double-sink 1.5 IN Double Cove Edge countertop overview.
Original source page 9, visually unchanged. Read this page's text equivalent.
View and dimensional relationships
Perspective of a rectangular double-sink countertop with two rounded-corner sink openings, one faucet hole behind each, and a full rear backsplash. The title identifies 84 IN DOUBLE SINK 1.5 IN DOUBLE COVE EDGE. Layered molded front, side edges and backsplash are depicted. No dimension-line callouts occur on this overview.
No dimension callouts are printed on this overview page.
Source page 10: Double-cove countertop and backsplash
View original PDF — Source page 10: Double-cove countertop and backsplash
Original drawing: Double-cove countertop and backsplash.
Original source page 10, visually unchanged. Read this page's text equivalent.
View and dimensional relationships
Separate backsplash elevation and side profile sit above a long edge elevation. Below, the plan shows two rectangular rounded-corner sink openings, two faucet holes and eight bracket-hole symbols. Separate horizontal chains locate faucet axes, opening edges and bracket columns; vertical chains locate opening edges, faucet center and bracket rows. A narrow edge section appears at the right.
The title is 84 IN DOUBLE SINK 1.5 IN DOUBLE COVE EDGE COUNTERTOP. Detailed profile labels separately print 1-5/8 inch /40 mm. The source limits these dimensions to Double Cove Edge and refers other styles to the Straight Mitered section. The rear inset literally reads 1/1 inch /25 mm; its intended wording remains unconfirmed.
On a narrow screen, scroll the measurement table horizontally to read every column. With a keyboard, focus the table region and use the left and right arrow keys.
| Measurement | Inches | Millimeters | Reference points / meaning |
|---|---|---|---|
| Backsplash length | 81-7/8 | 2080 | Full horizontal span of the separate backsplash elevation. |
| Backsplash height | 3-7/8 | 100 | Vertical span of the separate backsplash, not countertop profile height. |
| Backsplash thickness | 3/4 | 20 | Horizontal span of the narrow backsplash end view. |
| Front elevation profile height | 1-5/8 | 40 | Vertical profile-height dimension on the left of the front edge elevation. |
| Front elevation layer 1 | 3/4 | 20 | Separate upper layer thickness at the right of the front elevation. |
| Front elevation layer 2 | 3/4 | 20 | Separate lower layer thickness at the right of the front elevation. |
| Plan overall width | 84 | 2134 | Outside left-to-right span of the countertop in plan. |
| Left faucet-axis offset | 24-7/8 | 632 | Left outside edge to left faucet-hole centerline. |
| Faucet-axis spacing | 34-1/4 | 870 | Horizontal distance between the two faucet-hole centerlines. |
| Right faucet-axis offset | 24-7/8 | 632 | Right faucet-hole centerline to right outside edge. |
| Plan overall depth | 22 | 560 | Rear outside edge to front outside edge of the countertop. |
| Rear edge to sink opening | 5-1/2 | 140 | Upper segment of the left vertical chain, rear outside edge to rear edge of the left sink opening. |
| Sink opening depth | 12-1/4 | 310 | Middle segment of the left vertical chain across the opening from rear to front. |
| Sink opening to front edge | 4-3/8 | 110 | Lower segment of the left vertical chain, opening front edge to countertop front edge. |
| Rear edge to faucet center | 2-3/4 | 70 | Short vertical span near the left faucet hole, from the rear edge to its center. |
| Faucet-hole circular callout | 1-3/8 | 35 | Leader to the circular left faucet hole; the printed circular-hole size is preserved. |
| Rear edge to rear bracket row | 6-3/4 | 170 | Upper segment of the internal bracket-location chain from rear edge to rear bracket row. |
| Bracket-row separation | 9-7/8 | 250 | Middle segment between the rear and front bracket-location rows. |
| Front bracket row to front edge | 5-1/2 | 140 | Lower segment from front bracket row to outside front edge. |
| Left outside edge to left opening | 16-1/4 | 412 | First segment in the opening-edge chain beneath the plan. |
| Left sink opening width | 17-3/8 | 440 | Second segment across the left sink opening. |
| Solid span between openings | 16-7/8 | 430 | Middle segment between the inside edges of the two openings. |
| Right sink opening width | 17-3/8 | 440 | Fourth segment across the right sink opening. |
| Right opening to right outside edge | 16-1/4 | 412 | Last segment of the opening-edge chain. |
| Left outer bracket offset | 14 | 355 | Left outside edge to outer bracket column of the left sink. |
| Left bracket-column spacing | 21-3/4 | 554 | Horizontal spacing between bracket columns around the left sink. |
| Gap between inner bracket columns | 12-1/2 | 316 | Horizontal gap between the inner bracket columns of the two sinks. |
| Right bracket-column spacing | 21-3/4 | 554 | Horizontal spacing between bracket columns around the right sink. |
| Right outer bracket offset | 14 | 355 | Outer bracket column of the right sink to right outside edge. |
| Right side-profile height | 1-5/8 | 40 | Transverse span across the narrow right-hand profile view, independently repeated from the elevation. |
| Rear inner-border offset | 1/1 | 25 | Small vertical rear-edge to dashed-inner-line dimension at the top-right of the plan. Literal unusual fraction retained.Unresolved: PK84-P10-REAR |
| Right inner-border offset | 2 | 50 | Short horizontal span between the right outside edge and nearby dashed inner reference. |
| Front inner-border offset | 2 | 50 | Short vertical span between the front outside edge and nearby dashed inner reference. |
| Sink opening corner notation | Not printed | Not printed | Literal source notation 4-R20 with a leader to a rounded sink-opening corner. No unit is printed beside the notation, so no unit or conversion is invented. |
Source note: The source states: All measurements are plus or minus 1/4 inch. Values are copied as printed, not converted or approved for installation.
Source and assistance
View the original source PDF. Source reviewed 19 November 2026.
Request an accessible format or a confirmed drawing, or call Willow Bath and Vanity at (877) 788-8444.